Hello Dear, Who has a board from DJI Mini 3 Pro? If it is not difficult, please help to find out which components and with what value should be on the board marked in red. I will be very grateful!

Здравствуйте Уважаемые, У кого имеется плата от DJI Mini 3 Pro ? Если не трудно, будте добры помочь выяснить, какие компоненты, и с каким номиналом должный стоять на плате отмечеными красным. Буду очень благодаоень!

⟐ Edited by author октября 23, 2024 at 19:02 GMT-7

⟐ Answered августа 12, 2024 at 7:21 GMT-7

⟐ Answered июня 04, 2026 at 1:59 GMT-7

⟐ Answered мая 26, 2026 at 11:37 GMT-7

Before repair:

• Jello (tried new OEM props, no effect)
• After flying away for a couple minutes, error 40003 (gimbal motor overloaded) would appear
• Footage looked fine besides the jello, but previous owner reported the gimbal would sometimes tilt as well
• Gimbal looked slightly damaged, but everything was intact and all axes rotated freely, both manually and when stabilising the camera

Repair:

• Replaced gimbal (including mounting board and dampers), but kept the original camera module and cables which did not look damaged
• Recalibrated gimbal using python

Issues after repair:

• Jello (even before arming, which I didn't know was possible)
• Error 40003 soon after powering on, much sooner and more consistently than before
• Gimbal is tilted and not centered
• DJI fly gimbal calibration stops at 10%
• Error 40011 (gimbal calibration failure) (I believe this is normal after using the python method to calibrate the gimbal, but it should still be fully functional)

⟐ Commented мая 16, 2026 at 18:24 GMT-7

I purchased a Mavic Air 2S from EBay but I’m getting an error on the DJI Fly app that says

“Aircraft bound to another account. Change account and try again.”

I tried to reach the seller and no response. Is it possible to “unbind” the Air 2S from the previous owners DJI account?

⟐ Answered мая 13, 2026 at 22:19 GMT-7

The damage is quite severe and has affected the surrounding pads and traces. I am looking for a schematic, boardview, or a high-resolution reference photo of this specific area to identify the values of the nearby capacitors and resistors that were also damaged.

Has anyone successfully repaired this rail or can provide a partial schematic/pinout for this "AUM" chip on the Mini 3 Pro board? Any help with component values in this area would be greatly appreciated.

• Replaced front left arm
  • Broke GPS ribbon cable
  • Small plastic cube came off the gimbal cable
• Replaced GPS ribbon cable with one from a M4p
  • Now flies
  • Gimbal stuck error (yaw/roll don't move, but all axes move manually)
• Replaced gimbal cable with one from a M4p
  • Damaged pitch motor ribbon cable during disassembly, replaced arm and motor with one from a M4p
  • Gimbal is now detached from the drone
  • No errors, gimbal moves when held
• Reattached gimbal
  • Gimbal does not move, no video feed
  • Tons of errors (see pictures)

I'm confused by the downward vision sensor error. I didn't mess with anything but the gimbal after I got it working while detached other than to try and address these issues.

⟐ Answer accepted мая 06, 2026 at 10:30 GMT-7

⟐ Edited мая 03, 2026 at 22:03 GMT-7

⟐ Commented апреля 28, 2026 at 9:07 GMT-7

⟐ Commented апреля 25, 2026 at 14:12 GMT-7