Hello Dear, Who has a board from DJI Mini 3 Pro? If it is not difficult, please help to find out which components and with what value should be on the board marked in red. I will be very grateful!

Здравствуйте Уважаемые, У кого имеется плата от DJI Mini 3 Pro ? Если не трудно, будте добры помочь выяснить, какие компоненты, и с каким номиналом должный стоять на плате отмечеными красным. Буду очень благодаоень!

⟐ Edited by author октября 23, 2024 at 19:02 GMT-7

⟐ Answered августа 12, 2024 at 7:21 GMT-7

I purchased a Mavic Air 2S from EBay but I’m getting an error on the DJI Fly app that says

“Aircraft bound to another account. Change account and try again.”

I tried to reach the seller and no response. Is it possible to “unbind” the Air 2S from the previous owners DJI account?

⟐ Commented июля 30, 2026 at 1:04 GMT-7

⟐ Commented июля 27, 2026 at 23:49 GMT-7

Before repair:

• Jello (tried new OEM props, no effect)
• After flying away for a couple minutes, error 40003 (gimbal motor overloaded) would appear
• Footage looked fine besides the jello, but previous owner reported the gimbal would sometimes tilt as well
• Gimbal looked slightly damaged, but everything was intact and all axes rotated freely, both manually and when stabilising the camera

Repair:

• Replaced gimbal (including mounting board and dampers), but kept the original camera module and cables which did not look damaged
• Recalibrated gimbal using python

Issues after repair:

• Jello (even before arming, which I didn't know was possible)
• Error 40003 soon after powering on, much sooner and more consistently than before
• Gimbal is tilted and not centered
• DJI fly gimbal calibration stops at 10%
• Error 40011 (gimbal calibration failure) (I believe this is normal after using the python method to calibrate the gimbal, but it should still be fully functional)

The damage is quite severe and has affected the surrounding pads and traces. I am looking for a schematic, boardview, or a high-resolution reference photo of this specific area to identify the values of the nearby capacitors and resistors that were also damaged.

Has anyone successfully repaired this rail or can provide a partial schematic/pinout for this "AUM" chip on the Mini 3 Pro board? Any help with component values in this area would be greatly appreciated.

• Replaced front left arm
  • Broke GPS ribbon cable
  • Small plastic cube came off the gimbal cable
• Replaced GPS ribbon cable with one from a M4p
  • Now flies
  • Gimbal stuck error (yaw/roll don't move, but all axes move manually)
• Replaced gimbal cable with one from a M4p
  • Damaged pitch motor ribbon cable during disassembly, replaced arm and motor with one from a M4p
  • Gimbal is now detached from the drone
  • No errors, gimbal moves when held
• Reattached gimbal
  • Gimbal does not move, no video feed
  • Tons of errors (see pictures)

I'm confused by the downward vision sensor error. I didn't mess with anything but the gimbal after I got it working while detached other than to try and address these issues.

⟐ Answer accepted мая 06, 2026 at 10:30 GMT-7

Current setup:

- DJI Fly App version: 1.20.0

- Aircraft Firmware: 01.00.0600 (latest version)

- Battery level: Above 50%

- Surface: Flat and level

- Arms: Folded in

I have already tried restarting the drone, controller, and app multiple times. I have also tried the correct power-on sequence (controller then drone). What could be preventing the calibration from starting? Is this a known software bug with this app version, or does it indicate a total hardware failure of the IMU chip on the motherboard?

⟐ Commented апреля 08, 2026 at 4:57 GMT-7

⟐ Answered марта 31, 2026 at 20:22 GMT-7