только только купила прошитую нинтендо свитч олед с авито, все было нормально. приехала домой и захотела установить игру. на нее не устанавливалось обновление потому что прошивка была старой (ультра 2.6), и я в интернете смотрела что то обновила и в итоге потом DBI выдавал мне ошибку при заходе в него «программа закрыта, потому что произошла ошибка». и мне предложили удалить DBI через hekate там через пк в tools > usb tools > sd card и там через пк я удаляла ее в разделе свитч. и потом зашла и нет DBI (хотя говорили что появится почему то) и теперь все программы в sphaira не открывается и вылазит та же самая ошибка. можете чем нибудь помочь пожалуйста? 🥹 я просто глупо что то натыкала, просто пыталась понять как обновить прошивку и теперь ужасно волнуюсь, плачу и не знаю что сделать боюсь что она вообщк кирпичом станет

⟐ Answered июля 28, 2026 at 12:18 GMT-7

⟐ Answered марта 12, 2025 at 2:51 GMT-7

Has anyone else experienced this?

⟐ Commented июля 25, 2026 at 3:59 GMT-7

Switch 2 with both charging ports damaged. Replaced both ports and only 2 data lines were damaged on the main bottom port. Installed new lines and they show good on tester. There were 6 total ground lines damaged. 3 on top and 3 on the bottom. Replaced both ports and both ports are getting .512 amps. System is not jumping to the next stage to charge or turn on system. Not sure where to look on these. I don't see anything like a M92/P13/BQ or caps that test/look bad. Has anyone else had anything similar that was obvious? Much thanks for any guidance.

⟐ Commented июля 22, 2026 at 22:15 GMT-7

⟐ Commented июля 19, 2026 at 10:12 GMT-7

My game card catridge reader isnt working anymore(the pins got bent or broken). Any ideas where I could order a replacement part? And if there is any, since the console is like 6 months old.

Ty

⟐ Answered июля 17, 2026 at 15:16 GMT-7

Does anyone has the bottom rail for the red mario edition switch oled? Or can i request the part on a site like this, or elsewhere?

Bought a mint switch oled mario for a cheap price. The only thing what is wrong, is the bottom rail molten. Finding this piece is easier said than done. Thanks!

Mike

⟐ Commented июля 17, 2026 at 5:15 GMT-7

⟐ Commented июля 12, 2026 at 23:56 GMT-7

⟐ Answered июля 12, 2026 at 23:42 GMT-7

Has anyone tried this method? If so, are there any specific pitfalls I should watch out for? Also, are there existing guides I can use as prerequisites for removing the motherboard or midframe to make the process smoother for users? I want to make sure the guide is as efficient as possible while still being safe.

⟐ Answer accepted июля 10, 2026 at 6:21 GMT-7

I recently successfully replaced the M92T36 IC on a Nintendo Switch motherboard using a hot air station. The console now boots up and charges normally. However, I am now facing an issue with the Right Joy-Con.

When I slide the right Joy-Con into the rail, the console does not detect it as attached (it stays on wireless mode). I opened up the console again to inspect the area and noticed that the ribbon cable and the FPC connector look perfectly fine.

However, upon closer inspection of the small SMD component cluster right next to the FPC connectors, I noticed that one SMD component at the very bottom of the row is completely missing (likely blown away or knocked off accidentally during my hot air rework of the M92T36).

I have attached a micro photo of my board showing the missing component's empty pads, alongside some reference screenshots from the iFixit teardown guide for comparison.

My questions are:

1. Is this missing component a resistor (in-series) or a filter/bypass capacitor (to GND)?

2. What is the exact value/specification of this missing component (looks like a 0402 package)?

3. If it is a resistor on a data/detection line, can I safely bridge the pads with solder or a jumper wire to restore the detection functionality?

I have a multimeter, soldering iron, and hot air station ready to fix this. Any guidance or schematic insights would be greatly appreciated!

Thanks in advance for your help!

Nintendo Switch 2 has IC chip fried, need a replacement, Ive found out the type of chip theyre using CP10359at, and at other website its identified as cypd6228-96bzxi,,would this be a correct replacement to have it repaired? Can I buy CP10359at chip here?

Currently the Switch is not charging and battery has died.

⟐ Commented июля 08, 2026 at 15:00 GMT-7

What are some other ways to remove such a small, recessed, and stripped Tri-point screw without damaging the plastic shell? I don't want to drill it out if I can avoid it. Any advice from people who have dealt with this specific Joy-Con issue would be appreciated!

⟐ Commented июля 06, 2026 at 22:09 GMT-7

⟐ Answered июля 04, 2026 at 19:56 GMT-7

⟐ Commented июля 01, 2026 at 7:30 GMT-7

I finally bought a replacement battery and swapped it, at the start it just showed the Nintendo logo and went black but I left it to charge overnight and when I checked it, it showed the low battery icon which I thought it was a good sign. It is as of now 4 days straight charging (more than 100hs) and it is going back and forth between showing nothing unless I try the hold the power button for 20 secs hard reset and showing the low battery icon

When I opened it I saw it has part of a mod chip soldered to the board, I didn't knew about that and the seller didn't tell me either. I was worried it might have some board issue, but I don't fully know. I gets warm so I think it is charging, but still no sign of life

I mostly would like to know if there is some quirk about swapping batteries that I might be doing wrong, I heard that the charging time of a fully drained battery was long, but is it this long? Or if there might be a board issue and it's an unfixable Switch

Sorry for the long text, but I thought context might be needed and it's my first time messing with a Switch (also, English isn't my first language)

⟐ Answered июня 30, 2026 at 23:56 GMT-7

⟐ Answered июня 30, 2026 at 2:06 GMT-7

I allready replaced the flex cable.

Same behaviour. Vol + not working, Vol - and Power are working.

Any idea, what could cause this problem?

⟐ Commented июня 30, 2026 at 2:05 GMT-7

To add, before I replaced it, it was not going left or right. Replaced it and still does the same thing.

⟐ Answered июня 28, 2026 at 18:18 GMT-7