iFixit - Answers With Device "Pressure Washer"

Ryobi Pressure Washer RY14122 2013: Removing hose from spray gun and pump housing

Tue, 05 Aug 2025 02:10:17 -0700

How do you remove the spray hose from the spray gun and the pump housing? Rubber gaskets seem to be frozen on place. I don't what to force it and possibly damage something. I'm missing something.

⟐ Answer accepted августа 05, 2025 at 2:10 GMT-7

Honda GCV160 Pressure Washer: Where is the fuel filter? What is the replacement unit?

Thu, 08 May 2025 00:05:12 -0700

Where is the fuel filter?

⟐ Answer edited мая 08, 2025 at 0:05 GMT-7

Craftsman Pressure Washer 58075254 2017: Is this unit a 4 or 2 cycle engine?

Thu, 01 May 2025 16:45:39 -0700

See title for question.

⟐ Answered мая 01, 2025 at 16:45 GMT-7

Craftsman Pressure Washer 58075271 2014: How much oil goes in the pump?

Thu, 19 Sep 2024 18:23:12 -0700

How much pump oil goes in the pump

⟐ Answer edited сентября 19, 2024 at 18:23 GMT-7

Ryobi Pressure Washers RY80942 2020: Where can I buy the uploader valve

Mon, 13 May 2024 16:15:39 -0700

where can i buy the uploader valve

⟐ Commented мая 13, 2024 at 16:15 GMT-7

Craftsman Pressure Washer 580752501 2011: How can I buy a fuel tank

Mon, 06 Nov 2023 20:44:37 -0700

How do I buy a fuel tank

⟐ Answer edited ноября 06, 2023 at 20:44 GMT-7

Pressure Washer: Name this part: Craftsman electric pressure washer model 99016

Sun, 17 Sep 2023 10:34:56 -0700

Massive water leak and loss of pressure on Craftsman electric pressure washer model 99016. Teardown revealed a break in this water line component (should be one piece instead of two), measures about 3” x 4”. Unable to find a parts diagram for the internal workings; the diagram in the manual only contains external components like nozzles and detergent tanks. Purchased the unit on 6/8/2017 prior to the closure of our local Sears, not that long ago in my opinion, yet Sears Parts Direct cannot locate this model number. Without knowing the part number or even what to call it, our conversation went nowhere. Somewhere in the world there is box of these parts sitting on a shelf. Please help me find them!

In the event my search is futile, any advice on a workaround? JB Weld is the only trick on my mind at the moment.

⟐ Commented сентября 17, 2023 at 10:34 GMT-7

MiTM Pressure Washers CA3504HDHB 2012: Looking for a part that broke

Wed, 07 Jul 2021 07:59:01 -0700

Good morning,

We have a Mi-T-M 3500 PSI and the part where it connects the water hose broke. Wanted to see if you can help us find what part will that be so we can order it. Thanks in advance!

⟐ Answered июля 07, 2021 at 7:59 GMT-7

Karcher Pressure Washers 11073090 2017: What is the part no of the unloader valve

Tue, 29 Dec 2020 00:56:00 -0700

What is the part number of the unloader valve

⟐ Answered декабря 29, 2020 at 0:56 GMT-7

Pressure Washer: Why won't my pressure washer turn off?

Fri, 24 Apr 2020 03:59:14 -0700

I have a Karcher electric pressure washer. It runs even when the power switch is turned off, but there is no pressure. Any suggestions?

⟐ Commented апреля 24, 2020 at 3:59 GMT-7

Pressure Washer: motor housing top bearing

Sun, 01 Sep 2019 08:08:58 -0700

what do you pack motor housing bearings with grease or oil ?

⟐ Answer deleted сентября 01, 2019 at 8:08 GMT-7

Pressure Washer: No pressure in my karcher2

Wed, 08 May 2019 06:52:33 -0700

I put a bin liner loosely over my karcher 2 because it started to rain,then went back to the spraying and forgot to take the bin bag off.

it ran for a while,then made a awful noise,and I was very quick to turn it off.it will turn on but there is no pressure,can you please help

⟐ Commented мая 08, 2019 at 6:52 GMT-7

Pressure Washer: Pump always on, lower pressure, water leaking

Mon, 18 Feb 2019 16:59:51 -0700

I have a Kärcher K 2.01

Recently, when turned on (= electricity switch on) but without pulling the trigger, it started to "kof", that is to turn its pump on and make the same noise as when you use it, but even when idle.

It did so in short bursts for a while.

Now, the pump is always on, even when you don't pull the trigger, there's a little less pressure (though still usable) and you can see quite a lot of water leaking out of the yellow box.

Is this repairable?

If yes, how?

Thanks

⟐ Answered февраля 18, 2019 at 16:59 GMT-7

Pressure Washer: Where can I get a CleanForce CF1800 HD repair manual?

Sat, 01 Sep 2018 13:01:28 -0700

Where can I get a CleanGorce CF1800 HD repair manual?

⟐ Commented сентября 01, 2018 at 13:01 GMT-7

Pressure Washer: My electric power washer shuts off after about five seconds

Fri, 18 May 2018 04:37:28 -0700

My Karcher electric pressure washer shuts off after about five seconds; I have to keep pulling the trigger to keep it running.

⟐ Commented мая 18, 2018 at 4:37 GMT-7

Pressure Washer: chemical injector screw snapped off and threaded piece still inside

Fri, 24 Nov 2017 13:16:14 -0700

the chemical injector nozzle that is screwed into pressure washer pump broke off and the threaded piece is still inside manifold.how can i get this out?

⟐ Answer accepted ноября 24, 2017 at 13:16 GMT-7

Pressure Washer: My washer won't shut off.

Sun, 30 Jul 2017 07:33:56 -0700

K2.26

The switch doesn't even operate, however it does run and does spay as it always has.

⟐ Answer accepted июля 30, 2017 at 7:33 GMT-7

Pressure Washer: Why does the motor appear to cut in and out?

Tue, 20 Jun 2017 15:01:03 -0700

The motor on my Karcher pressure washer has stopped running smoothly. It occasionally stops altogether as if overheating but does not appear hot. During operation it is constantly surging in power and then slacking off. Sorry for the un-technical description.

⟐ Commented июня 20, 2017 at 15:01 GMT-7

Craftsman Pressure Washer 58075241 2012: I need a new wheel it broke off where can I find one

Mon, 13 Apr 2026 11:28:04 -0700

Where can I find a wheel for the pressure washer it broke off

Craftsman Pressure Washer 58075287 2016: Stalls after starting with starting fluid

Sat, 07 Mar 2026 22:00:51 -0700

I know there’s no choke for this pressure washer. But I’ve used a bit of gas as starting fluid in the intake and filled the gas tank, but the engine dies after starting for a few seconds. The engine hasn’t ran for over a year. I’ve cleaned the carb and replaced the fuel lines from the gas tank. The bowl on the carb does fill with gas. I do need to replace the air filter foam and the carb bowl bolt gasket as it drips a bit of gas, but I’d think it’s run with those issues. Any tips?