⟐ Answered июля 07, 2023 at 3:41 GMT-7

устранить неисправность?

Online Translation.

how to repair the robot pilesos

vacuum cleaned. after the start , the display shows an error C- 01 as

troubleshoot ?

⟐ Answered декабря 28, 2021 at 7:09 GMT-7

⟐ Commented июля 30, 2026 at 0:09 GMT-7

recently the main brush motor stopped spinning so i opened it up to replace the motor. i have now bought 3 different replacement motors that say they are for the T8 or 8x. but none of them fit correctly. i have searched like crazy but can not for the life of my find my motor anywhere online. (pictures below) am i crazy? are these no longer in production? is one of the other motors supposed to fit even though the L shape is wrong? your wisdom is appreciated.

ok so with some inspiration from oldturkey03 i think im close. im going to walk through what i did if anyone else is ballzie enough to try this.

so i decided i was going to transfer the old L drive shaft to the new motor. i started by unclipping the snaps around the perimeter (picture1).

once inside i cleaned all the gears as they were very full of dirty grease (picture2).

i then removed the two screws on the left side of the image (picture3) (this is where the motor attaches) and screwed in the new motor.

but as i put it back together i realized that the gear attached to the new motor was beveled to the left but all the old gears were beveled to the right! so i pried the motor gear off of the old motor and transferred it to the new one. (be careful when prying off it toke a lot of force and mine ended up half way across the room in my white shag carpet. much cussing ensued.)

ive got all the pieces together and clean now i guess the last thing i need is to figure out what kind of lubricant to use on the gears. any ideas?

⟐ Commented июля 26, 2026 at 12:09 GMT-7

⟐ Commented июля 21, 2026 at 14:43 GMT-7

⟐ Commented июля 15, 2026 at 18:28 GMT-7

i bought a batrie to my roombai7 that you said that was compatible but my roomba said that not ricognize

⟐ Answered июля 11, 2026 at 18:48 GMT-7

I'm trying to figure out whether I'm dealing with a hardware fault or a software/firmware bug on my Roborock S7 Max Ultra.

Firmware: v02.26.80 (currently up to date, per the app)

The problem: After the robot finishes a cleaning cycle, it does not automatically empty its bin into the dock. This happens regardless of whether the auto-empty setting is on "Smart" or "Max."

What works fine:

If I manually trigger emptying from the app, it works perfectly every time. Even when the robot's onboard bin is completely packed full (mostly dog hair), the manual empty cycle pulls everything through into the dust bag in the dock with no issues.

What doesn't work:

• The automatic emptying after a cleaning run simply never triggers on its own.
• The bin indicator in the app never turns red/full, even when the bin is genuinely packed solid. The robot will happily keep cleaning with an already-full bin instead of stopping or flagging it.
• Eventually I do get an "empty ASAP" notification, but given the above, I suspect that's just timer-based (e.g. "X days since last empty") rather than tied to an actual full-bin reading.

Has anyone dealt with something similar? Is there a known sensor (e.g., bin-full sensor or dock contact sensor) that could cause this exact symptom, or is this more likely a bug that needs a factory reset or re-pairing to fix?

Any troubleshooting tips or shared experiences would be appreciated.

⟐ Answered июля 08, 2026 at 22:01 GMT-7

⟐ Commented июля 03, 2026 at 17:15 GMT-7

⟐ Answer edited июня 26, 2026 at 19:04 GMT-7