⟐ Commented сентября 20, 2025 at 9:02 GMT-7

Symptoms:

- While heating, the error flashes for ~1 second, the temperature display drops a few degrees, then heating resumes. This cycles repeatedly.

- Using firmware 1.5.0 on both Hub and Iron.

- Tip is a 1.5 Bevel.

Troubleshooting already performed:

- Verified tip is fully seated (clicked in, aligned below the surface).

- Cleaned 3.5mm contacts and internal handle springs with IPA.

- Disassembled the iron handle; internal soldering points for the socket are secure and show no signs of failure.

- Measured tip resistance at ~3 ohms at room temperature.

- Tested both front USB-C ports with the original cable (same result).

- Tested with third-party 100W cables (MacBook/IKEA), which resulted in Error #11 (No Data), confirming the hub requires the specific data lines of the original cable.

The intermittent nature suggests a thermal expansion break inside the tip's sensor circuit. Are there any known issues with this behavior or specific tests I can run to verify if it's the tip vs. the iron handle's internal logic?

⟐ Commented июня 02, 2026 at 22:48 GMT-7

⟐ Commented июня 02, 2026 at 10:55 GMT-7

I have already tried the following troubleshooting steps:

- Disabled both Idle and Sleep timers.

- Verified the physical switch is in the "On" (orange) position.

- Cleared the error log and performed a factory reset via the FixHub Web Console.

- Ensured firmware is up to date for both the iron and the power station.

- Tried multiple power sources, including the FixHub Power Station and a high-wattage USB-C PD plug.

- Reseated the soldering tip multiple times.

Despite these steps, the heater shuts off the moment it hits the set temperature. Is this a known firmware bug or a hardware failure in the main board or tip sensor?

⟐ Answered июня 01, 2026 at 11:24 GMT-7

⟐ Answer accepted июня 01, 2026 at 4:07 GMT-7

⟐ Answered мая 31, 2026 at 11:15 GMT-7

⟐ Answered мая 31, 2026 at 7:23 GMT-7

⟐ Commented мая 30, 2026 at 13:40 GMT-7

⟐ Answered мая 30, 2026 at 13:38 GMT-7

⟐ Commented мая 30, 2026 at 10:01 GMT-7

My Toro AWD personal pace recycler 22’ 168cc. Sounds like it idles higher then it should its like its off to the races or something.

I pulled off the decorative cover and took a look at the governor tension springs(I think that is what it is) located above the carburetor and no matter what I do loosen, tighten jiggle with the springs it does not change the idle speed at all, sounds the same no matter what I do.

Is there a way to adjust the idle on this lawn mower?

It runs good and starts right up just the idle sounds so dang high is this normal? This is a new to me mower - its used a couple years old and the person I bought if from said he thought it idled high also but did not know how to adjust it either.

Thank you so much. I’m baffled!

Hi- i figured it out yesterday. It’s a fixed throttle so there is no carb adjustment screws on the carbs. I did find the governor on it though and kind of rigged it to pull back a little farther on the carb by adding some wire so I did get it to idle down lower by doing this.

It works .. the way I did it (even though maybe not the correct way) I guess that is all that matters. :-)

Thank you for your suggestion.. very much appreciated.

⟐ Commented мая 30, 2026 at 9:12 GMT-7

⟐ Answered мая 29, 2026 at 22:46 GMT-7