Перейти к основному содержанию
Помощь

Текущая версия: Carlos Ferrari ,

Текст:

Well it does work!
First I had to fire up the multimeter and do a continuity test to figure it out which was what:
[image|1764280]
[image|1764283]
Then it was just a matter of sourcing a microscope and do some soldering (more of a pain than one might realise):
[image|1764281]
And it worked! :D
[image|1764282]
Now I have to find out where to get the receiver to work inside the case…
The small Apple in the front - the one previously used for this - is blocked by the power plug so I'm thinking either the big Apple on the back (which can be a pain plus not get good reception) or the vents in the bottom of the case (will be my first option).
UPDATE:
Got the IR sensor at the bottom, near the vents.
Tricky parts were:
-1) get the cable out of the way of the speaker (one of the pictures is blurry but is the best I could do)
+1) get the cable out of the way of the speaker (one of the pictures is blurry but is inside the case and it's the best I could do)
[image|1775885]
[image|1775884]
-2) get the damn thing facing down (this took AGES!)
+2) get the bloody thing facing down (this took AGES!)
[image|1775887]
-
-
And it works! You might need to sort of ‘aim’ the remote a bit but it works! :D

Статус:

open

Отредактировано: Carlos Ferrari ,

Текст:

Well it does work!
First I had to fire up the multimeter and do a continuity test to figure it out which was what:
[image|1764280]
[image|1764283]
Then it was just a matter of sourcing a microscope and do some soldering (more of a pain than one might realise):
[image|1764281]
And it worked! :D
[image|1764282]
Now I have to find out where to get the receiver to work inside the case…
The small Apple in the front - the one previously used for this - is blocked by the power plug so I'm thinking either the big Apple on the back (which can be a pain plus not get good reception) or the vents in the bottom of the case (will be my first option).
-Will update once it's finished :)
+UPDATE:
+
+Got the IR sensor at the bottom, near the vents.
+
+Tricky parts were:
+
+1) get the cable out of the way of the speaker (one of the pictures is blurry but is the best I could do)
+
+[image|1775885]
+
+[image|1775884]
+
+2) get the damn thing facing down (this took AGES!)
+
+[image|1775887]
+
+
+
+And it works! You might need to sort of ‘aim’ the remote a bit but it works! :D

Статус:

open

Отредактировано: Carlos Ferrari ,

Текст:

Well it does work!
First I had to fire up the multimeter and do a continuity test to figure it out which was what:
[image|1764280]
+
+[image|1764283]
Then it was just a matter of sourcing a microscope and do some soldering (more of a pain than one might realise):
[image|1764281]
And it worked! :D
[image|1764282]
Now I have to find out where to get the receiver to work inside the case…
The small Apple in the front - the one previously used for this - is blocked by the power plug so I'm thinking either the big Apple on the back (which can be a pain plus not get good reception) or the vents in the bottom of the case (will be my first option).
Will update once it's finished :)

Статус:

open

Оригинальный сообщение: Carlos Ferrari ,

Текст:

Well it does work!

First I had to fire up the multimeter and do a continuity test to figure it out which was what:

[image|1764280]

Then it was just a matter of sourcing a microscope and do some soldering (more of a pain than one might realise):

[image|1764281]

And it worked! :D

[image|1764282]

Now I have to find out where to get the receiver to work inside the case…

The small Apple in the front - the one previously used for this - is blocked by the power plug so I'm thinking either the big Apple on the back (which can be a pain plus not get good reception) or the vents in the bottom of the case (will be my first option).

Will update once it's finished :)

Статус:

open