Перейти к основному содержанию

AT&T’s Handset Phone answering system with the model number: EL52300.

6вопросов Показать все

Why does handset read Out of Range or No Power at Base?

When I am trying to place a call, the message says out of range even though I am close to the base

Отвечено! Посмотреть ответ У меня та же проблема

Это хороший вопрос?

Оценка 25
34 Комментариев

I have tried all the possible options to correct this. But the cordless head set still says out of range or no power at base. It seems that the base is not working. how can I fix this.

из

Having the same problem as Patty ANGLE

из

Just ran into this problem with our new office phones. You can reset the system by entering the following code followed by hitting the Menu/Select button: *331734#

из

Found this same solution here and elsewhere. The code is correct, but the key ingredient is to press the lefthand softkey after entering the code.

из

Thank you Judith, I was wondering what what wrong, 5 mins later after seeing your comment (not really) I pressed it and voila...ready to be paired to new base.

из

Показать 29 больше комментариев

Добавить комментарий

13 Ответов

Выбранное решение

Is the base to your phone on? That’ll make your phone think it is out of range. Next, make sure the phone is placed in the base for at least 5 minutes to reset its connection to the base, and then try placing a call after. If the problem still persists, there could be other signals messing up the connection. Check to see if there are any other cordless phones or ham radios around, and try turning them off. After that your phone should be able to connect.

Был ли этот ответ полезен?

Оценка 11

24 Комментариев:

I did all of the above instructions and it did not work. I drove off 2 days ago with phone away from the house and when I returned to put phone back on the base, it said "out of range or no power at base". Batteries are working in phone and the base lights up.

из

try taking the battery out and wait a couple minutes and put it back in..worked for me as my phone said the same thing.

из

That last comment is the answer. Worked with me. Thank you.

из

Since power outage, with winter storm, handset would not work! Still says no pwr

из

I've done all of the above still says the same thing~~ Could my power cord be bad can't get through to AT&T

из

Показать 19 больше комментариев

Добавить комментарий
Наиболее полезный ответ

Turns out I had to un-register mine first.

Here’s what worked for me after much fruitless googling:

Press Menu

*7890#

test handset

menu

sw version

next page

menu

register clear

menu

ok

press and hold the red ‘off’ button

After all that, it was ready to register, which was accomplished by simply placing it on the base. Voila!

Был ли этот ответ полезен?

Оценка 13

8 Комментариев:

No ring tone but rings in. Answer machine picks up. Says out of range or no power to base. This unit is a month old. Have unplugged and all of that.

из

Ruby Read thank you!!!!!!!! I have spent hours looking and your instructions above worked. On my phone next page was the top soft button and OK = Menu.

I can't believe it worked -- you made my week!!!! Brilliant:)

из

Had to remove battery because handset went dead. Once plugged back in it said to press Find Handset for 4 seconds. Now works fine. Thanks.

Mike

Rockville, MO

из

Thank you, it works for my VTech CS6919-2

из

Worked for me after power outage.

Ben Va.

из

Показать 3 больше комментариев

Добавить комментарий

i had the same problem with my phone...either it said out of range or no power to base..i unplugged the battery..waited a couple minutes and plugged back in and it works now.

Был ли этот ответ полезен?

Оценка 3

3 Комментариев:

It worked. Thanks

из

Perfect! Thank you!

из

@don53 Thanks ... this worked!! So simple, wish I saw this earlier.

из

Добавить комментарий

Forget all above!

On the handset enter 331734# then left soft key. If successful, the handset will show “Not registered.”

To register:

Place handset in the base (not the charge station)

Press “HOLD” for 4 seconds, then press # on handset.

This should appear on the handset display.

The handset shows “registering… please wait.”

you hear confirmation when complete.

Был ли этот ответ полезен?

Оценка 2

5 Комментариев:

Thanks so much for supplying the missing piece!

I’ve read the above solution in other places but it wasn’t working because I was pressing the wrong side soft key since there was never any indication where the actual menu was, so I kept pressing the one on the right. Finally here you cleared that up by specifying “left soft key”.

Just one minor but critical correction: Your code is missing the asterisk (star key), so it is actually *331734#

My handset works now!

из

Which is the left soft key ?

из

I have the Vtech LS6405. The instructions (*331734#) in my case were correct with exception that left soft key was actually the right soft key which was the talk button. Once done, beeped, worked like a charm, registered and now charging. Thank you very much as I was at the point of returning the phone. Thanks again

из

How do you put# and the * in?

из

Mine is Vtech doorbell IS7121-2 with the same problem on handsets; they are either out of range or no power at the base.

Any rest for this model?

из

Добавить комментарий

I had the same problem with my phone. First, make sure it's plugged in, if not, then it's obviously not going to work. But if it is plugged in, unplug it and wait a few minutes, then plug it back in. I found that my phone was actually unplugged. I plugged it back in and it is working now. So the first thing you should do before unplugging the phone, is make sure it is actually plugged in already.

Был ли этот ответ полезен?

Оценка 1
Добавить комментарий

I just unplugged the power cord from the base, waited two minutes and then plugged it in again and the problem went away. You might want to try this first before you try any of the other solutions because it is the simplest one. Also, make sure your batteries are good in the phone and all the extensions.

Был ли этот ответ полезен?

Оценка 1
Добавить комментарий

I tried all and finally found one solution googling:

1) In the Handset, press Menu

2) Then press *7890#

3) Press Down until find Test Handset, then press Select

4) Press Down until find Register Clear, then press Select.

5) Will ask if you want to Clear, Select Yes.

6) After some seconds it will put OK in the screen.

7) You will need to register the Handset again using to right method in the manual.

And that's all. And now My Vtech CS6929 it's working great!

Был ли этот ответ полезен?

Оценка 1

3 Комментариев:

Keeps asking to go to manual that I have list when I moved too my new place what can I do?

из

Brilliant! This worked for my AT&T Cordless Phone set. Reprogrammed all 3 phones and paired with my base unit. I was almost ready to toss everything in the trash. To register with my base unit after completing the steps above, I had to press and hold the 'find handset' button on my base unit until the light appeared. Then I pressed '#' on my handset to complete the registration process.

из

My model is EL52303. These instructions worked for me, except that I had an extra step: After "Test Handset" and then pressing SELECT, I had to go down, down, down until it said "Next Page=>" then I pressed SELECT again to get to "Register Clear"

Deregistered all 3 of my old handsets in less than a minute. Thanks so much! ra49:)

из

Добавить комментарий

I’m only a novice, but I always understood that if it was a newly installed phone system, the batteries had to be charged several hours before use. I’m getting that message right now and I called my husband (a telephone installer in the past) who verified what I just said. I will just use my cell phone until the message goes away, I guess. I’ve already tried every other suggestion offered here.

Был ли этот ответ полезен?

Оценка 0
Добавить комментарий

You likely need to de-register your phone first. Please follow the troubleshooting steps below:


NOTE: Handset must be in idle mode when performing the following procedures.


On the old handsets,


1. Press MENU/SELECT button then press *7890#.

2. Press ▼CID or ▲DIR until it shows “TO TEST HANDSET”, then press MENU/SELECT button.

3. Press ▼CID or ▲DIR until it shows “TO DE-REGISTER CLEAR”, then press MENU/SELECT button twice.

4. Hold down the OFF/CANCEL button until the display shows “OUT OF RANGE OR NO POWER AT BASE” or “Press HS LOC on base 4 sec”, then press MENU/SELECT button.


After this step, please reset the handset by taking the battery out for a minute then plug the battery back in.

Был ли этот ответ полезен?

Оценка 0

1 Комментарий:

which model phone was this?

из

Добавить комментарий

Really SIMPLE to fix the out of range/check base power issue

Press END and # hold down for 5 secs

Select BASE UNAVAILABLE and use center arrow key down to change to YES

That’s all you have to do, it is now ready to be registered.

Cheers

Allen

Был ли этот ответ полезен?

Оценка 0

1 Комментарий:

I dont have END button. What model do you have?

из

Добавить комментарий

Handset: Menu *331734 # Menu

Base: hold Handset Locator 4secs (will show “Registering”)

Wait a sec for handset to show “Registering”

Handset: #

Был ли этот ответ полезен?

Оценка 0
Добавить комментарий

es2310a vtech stated out of range blinking text

Был ли этот ответ полезен?

Оценка 0
Добавить комментарий

you can try to change battery or clean the battery box if the problem not fixed tried to dismantle the cover and clean the motherboard.

Был ли этот ответ полезен?

Оценка 0
Добавить комментарий

Добавьте свой ответ

Nam Mai будет вечно благодарен.
Просмотр статистики:

За последние 24часов: 44

За последние 7 дней: 229

За последние 30 дней: 932

За всё время: 171,623