Sony UBP X800 - Won't power on

Question

Blu-Ray Player

Guides and support for devices that play video from Blu-Ray Discs.

111вопросов Показать все

RagnarMop @ragnarmop

Репутация: 1

2

1

Опубликовано: 22 июл 2021 г.

Опции

Sony UBP X800 - Won't power on

Hi,

I’ve been trying to fix this device for some time and got some very helpful comments on another platform but that’s dried up so hoping I can get some pointers re where to go next :)

TLTR - I’ve pretty much eliminated the power module as the source of the problem as power seems to be leaving the board via 2 power cables to the mainboard.

I’m sure now its something on the motherboard but not sure what to check. Long shot I know, but if anyone has some ideas I can try, that would be greatly appreciated.

Thanks

Отвечено! Посмотреть ответ У меня та же проблема

Это хороший вопрос?

Да Нет

Оценка 0

2 Комментариев

@ragnarmop if you already ruled out the PSU we need to see the rest of the boards and we would need to know what you have already checked. That way we do not repeat unnecessary steps.

22 июл 2021 г. из oldturkey03

Hi there

I also have a completely dead UBP-X800. Just died while using the wifi. If you have a solution yet, PLEASE let us know, it would be appreciated.

30 авг 2021 г. из Kiss Apocolypse

Добавить комментарий

4 Ответов

Выбранное решение

RagnarMop @ragnarmop

Репутация: 1

2

1

Опубликовано: 29 июл 2021 г.

Опции

Gonna close this down now as I am pretty certain we can’t go any further. I am 98% certain that the fault is on the logic board and that is not a part I can either fix or replace as Sony no longer supply them. Oldturkey03, many thanks for your help! Stay well :)

Был ли этот ответ полезен?

Да Нет

Оценка 0

1 Комментарий:

Just to say my UBP x700 has same problem. A repair centre has told me it’s the board and £200 to repair so that’s the end of that.

21 янв 2022 г. из Shaun Kemp

Добавить комментарий

@ragnarmop if you already ruled out the PSU we need to see the rest of the boards and we would need to know what you have already checked. That way we do not repeat unnecessary steps. — oldturkey03
Hi there

I also have a completely dead UBP-X800. Just died while using the wifi. If you have a solution yet, PLEASE let us know, it would be appreciated. — Kiss Apocolypse
Just to say my UBP x700 has same problem. A repair centre has told me it’s the board and £200 to repair so that’s the end of that. — Shaun Kemp

oldturkey03 @oldturkey03 Репутация: 785к 1,1к 894 2,3к · Answer 1 · 2021-07-22T10:23:50-07:00

Наиболее полезный ответ

oldturkey03 @oldturkey03

Репутация: 785к

1,1к

894

2,3к

Опубликовано: 22 июл 2021 г.

Опции

@ragnarmop start by following the troubleshooting flowchart. Let us know what you find out.

@ragnarmop you are giving up to early :-) I finally got my hands on the complete service manual. Use that to complete the troubleshooting. ==>>Slide 1<<==

The schematic is a bit weird to look at. It is in layers and I am not sure how to open the individual layers in a PDF and have not had time to play around with it. It’s getting a bit crazy at work….again.

Don’t give up yet!

Был ли этот ответ полезен?

Да Нет

Оценка 3

20 Комментариев:

Hi!

Thank you for the flowchart. I’ll crack on and see what I find.

Regards!

22 июл 2021 г. из RagnarMop

Hi,

I should have mentioned that I’d bought a new power board and tried that but the player did not respond.

With the old board in place, I got the following result when testing the IC101: Testing voltage between pins 5 and 1 = 213V… Will keep testing.

23 июл 2021 г. из RagnarMop

Testing continues :)

Check power throughput from the board to CN202

With the device connect to mains, I checked pins 6 and 4 and there is no power getting to these pins. Its odd, When I tried the new board, it also did not return the player to life which suggests there’s something downstream perhaps? But why would there be no voltage showing on those pins if the problem was further down…… (thinking out loud here :) ) I have very little experience with electronics so everything is a first for me.

23 июл 2021 г. из RagnarMop

@ragnarmop did you check IC401 pin 4 and did you get 1.8V?

23 июл 2021 г. из oldturkey03

I found what I think you are referring to on the MB. Testing now.... I get 000 Volts at pin 4

23 июл 2021 г. из RagnarMop

Показать 15 больше комментариев

Добавить комментарий

relly shemesh @rellyshemesh Репутация: 1 1 · Answer 2 · 2023-01-31T07:23:28-07:00

relly shemesh @rellyshemesh

Репутация: 1

1

Опубликовано: 31 янв 2023 г.

Опции

I don't think they intended it to be fixed at all, even the service manual does not mention anything about it.

I think the best and easiest way is to use an external power supply or a power brick, doesn't matter, as long as it's 12V and 2A and above, this should do the job.

Был ли этот ответ полезен?

Да Нет

Оценка 0

Добавить комментарий