The changed portions from Ver. 1.0 are shown in blue.
4-3. MAIN BLOCK
4-3-1. Rear Cabinet Section
• Disassembly order
| No. | Part | Item | Note |
|---|---|---|---|
| 1 | Cabinet (Rear) Assy | #212 or #293 x 5 Claw x 3 | Refer to Note 1. |
| 2 | Side Cabinet (R) | ||
| 3 | Side Cabinet (L) | ||
| 4 | DC Lid | Claw x 1 | |
| 5 | SW-1002 Board | Claw x 2 Connector x | 1 |
| 6 | LCD Module | Claw x 3 Connector x | 1 |
| 7 | Cabinet (Front) Assy | #212 or #293 x 1 | Refer to Note 1. |
| 8 | Cabinet (Upper) Assy | #287 x 1 Claw x 3 | |
| 9 | Charging Capacitor | Discharging of the Charging Capacitor. |
Table Caption: This table lists components, their quantities, and associated notes for assembling a device, potentially involving cabinets, internal boards, and a charging capacitor.
Note1
For the combination of cabinet's color and screw, please refer to Table 1-1.
Table 1-1
| Screw's Ref. No. (Parts Color.) | Cabinet's Color |
|---|---|
| #212 (Silver) | PINK/SILVER/VIOLET |
| #293 (Black) | BLACK |
Table Caption: This table lists screw reference numbers and their corresponding parts' colors alongside the cabinet colors with which they are used. It shows that screw #212 (Silver) is used with PINK/SILVER/VIOLET cabinets, while screw #293 (Black) is used with BLACK cabinets.
Ver. 1.1 2014.02
The changed portions from
Ver. 1.0 are shown in blue.
4-3-2. Main Section
| No. | Part | Item |
|---|---|---|
| 1 | RL-1003 Board, Flash Unit | Boss x 1 Connector x 2 |
| 2 | MA-1004 Flexible Board | |
| 3 | Main Frame | Claw x 1 |
| 4 | DOC radiation Sheet | |
| 5 | MF Spacer | Claw x 1 |
| 6 | Lens Block | Connector x 2 |
| 7 | SP Sheet Metal | |
| 8 | SY-1035 Board | |
| 9 | Loudspeaker (1.0cm) | Solder x 2 |
Table Caption: This table lists parts and their associated components required for assembly, with items such as connectors, claws, and solder specified for certain parts.
4-3-3. Complementary Information
(1) Installation Method of Battery Terminal Board
4-4. LENS BLOCK
4-4-1. Removal and Installation
(1) Ornamental Ring A Replacing Method Removal
- 1 Turn on the power switch and extend the lens (TELE end).
- 2 Detach the battery.
- 3 Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
- 4 Turn the Ornamental Ring A clockwise and counterclockwise to detach it.
Note: As for the figure below, this model and the shape of the main body are different.
- 5 Disengage the four claws and remove the Barrier Assy.
Installation
- 1 Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy.
(2) DC Motor Worm Assy Replacing Method Removal
- 1 Disengage the two claws and remove the FG Leaf Spring.
- 2 Remove the two Sensors.
- 3 Disengage the three ribs and the boss, and then disconnect the connector.
- 4 Remove the boss.
- 5 Remove the four screws and detach the Rear Mirror Plate .
- 6 Remove the GearWorm Wheel, Gear A, and Gear B.
- 7 Remove the solder at two locations to detach the DC MotorWorm Assy and remove the two screws.
Installation
- 1 Install the DC Motor Worm Assy to the Stationary Tube Assy with two screws.
- 2 Solder the DC Motor Worm Assy onto the Flexible Board at two locations.
- 3 Turn the Gear in the
