Найдите ответы в этом документе
Мы прочитали все страницы 60, так что Вам не нужно этого делать. Задайте вопрос и получите ответ прямо сейчас.
Panasonic_DMC_TZ3.pdf
LUMIX
LEICA
DC VAAIO-ELMAA
ORDER NO. DSC0703019CE B26
Digital Camera
DMC-TZ3P DMC-TZ3PC DMC-TZ3PL DMC-TZ3EB DMC-TZ3EE DMC-TZ3EF DMC-TZ3EG DMC-TZ3EGM DMC-TZ3GC DMC-TZ3GD DMC-TZ3GK DMC-TZ3GN DMC-TZ3GT DMC-TZ3SG
DMC-TZ2P DMC-TZ2PC DMC-TZ2PL DMC-TZ2EB DMC-TZ2EE DMC-TZ2EF DMC-TZ2EG DMC-TZ2EGM DMC-TZ2GC DMC-TZ2GD DMC-TZ2GK
© 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
DMC-TZ2GN DMC-TZ2GT
Vol. 1 Colour
(S)...........Silver Type
(K)...........Black Type (except DMC-TZ2PL/GD/GT)
(A)...........Blue Type
(only DMC-TZ3P/PC/EB/EE/EF/EG/ EGM/GC/SG)
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public:. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product:. Products powered by electricity should be serviced or repaired only by experienced professional technicians: attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious or death: Any injury
TABLE OF CONTENTS
| PAGE | |
|---|---|
| 1 Safety Precaution --- | 3 |
| 1.1. General Guidelines ---3 | |
| 1.2. Leakage Current Cold Check | ---3 |
| 1.3. Leakage Current Hot Check (See Figure 1.)---3 | |
| 1.4. How to Discharge the Capacitor on Flash PCB---4 | |
| 2 Warning --- | 5 |
| 2.1. Prevention of Electrostatic Discharge (ESD) to ElectrostaticallySensitive (ES) Devices ---5 | |
| 2.2. How to Recycle the Lithium Ion Battery (U.S. Only)---5 | |
| 2.3. Caution for AC Cord(For EB/GC/SG)---6 | |
| 2.4. How to Replace the Lithium Battery---7 | |
| 3 Service Navigation | --- 8 |
| 3.1. Introduction | ---8 |
| 3.2. General Description About Lead Free Solder (PbF) ---8 | |
| 3.3. Important Notice 1:(Other than U.S.A. and Canadian Market) ---8 | |
| 3.4. How to Define the Model Suffix (NTSC or PAL model)---9 | |
| 4 Specifications --- | 12 |
| 5 Location of Controls and Components --- | 13 |
| 6 Service Mode --- | 15 |
| 6.1. Error Code Memory Function | ---15 |
| 6.2. Confirmation of Firmware Version | ---18 |
| 7 Service Fixture & Tools --- | 19 |
| 7.1. Service Fixture and Tools | ---19 |
| 7.2. When Replacing the Main PCB | ---20 |
| 7.3. Service Position ---20 | |
| 8 Disassembly and Assembly Instructions --- | 22 |
| 8.1. Disassembly Flow Chart---22 | |
| 8.2. PCB Location---22 | |
| 8.3. Disassembly Procedure | ---23 |
| 8.4. Disassembly Procedure for the Lens | ---28 |
| 8.5. Assembly Procedure for the Lens | ---31 |
| 8.6. Removal of the CCD Unit ---35 | |
| 8.7. Removal of the Zoom Motor Unit | ---35 |
| 8.8. Removal of the Focus Motor Unit | ---36 |
| 8.9. The Applyment of Grease Method---36 | |
| 9 Measurements and Adjustments --- | 37 |
| 9.1. Matrix Chart for Replaced Part and Necessary | |
| Adjustment---37 | |
| Maintenace --- | 38 |
| 10.1. Cleaning Lens and LCD Panel | ---38 |
Table Caption: This table of contents outlines a service manual, covering safety precautions, warnings, service navigation, specifications, component locations, service modes, necessary tools, disassembly and assembly procedures for various parts including PCBs, motors, and lenses, as well as measurement and adjustment guidelines, and general maintenance.
PAGE
1
Safety Precaution
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-RADIATION, shock, fire, or other hazards. Do not modify the original design without permission of manufacturer.
- An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
- When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
- After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
- After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2. Leakage Current Cold Check
- Unplug the AC cord and connect a jumper between the two prongs on the plug.
- Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1 M Ω and 5.2 M Ω . When the exposed metal does not have a return path to the chassis, the reading must be infinity.
1.3. Leakage Current Hot Check (See Figure 1.)
- Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
- Connect a 1.5 k Ω , 10 W resistor, in parallel with a 0.15 μ F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1.
- Use an AC voltmeter, with 1 k Ω /V or more sensitivity, to measure the potential across the resistor.
- Check each exposed metallic part, and measure the voltage at each point.
- Reverse the AC plug in the AC outlet and repeat each of the above measurements.
- The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
Hot-Check Circuit
1.4. How to Discharge the Capacitor on
Зарегистрируйтесь на iFixit бесплатно, чтобы прочитать полный текст документа (60 страниц)
Нам нужна бесплатная учетная запись, чтобы блокировать ботов и сохранить iFixit для людей.