Перейти к основному содержанию
  1. Use an opening tool to pry up the small rubber cover on the upper right corner of the RAM access door. Use an opening tool to pry up the small rubber cover on the upper right corner of the RAM access door.
    • Use an opening tool to pry up the small rubber cover on the upper right corner of the RAM access door.

  2. Remove the 5.3 mm Phillips #00 screw securing the RAM access door.
    • Remove the 5.3 mm Phillips #00 screw securing the RAM access door.

    • This screw is held in the hole in the door with a washer and will not come out of the hole, even after you unscrew it.

  3. Insert the point of an opening pick in the seam near the top right corner of the RAM access door and gently pry the door up slightly. The door is held in place by small clips around its edges. Pry until you feel the nearest clips release.
    • Insert the point of an opening pick in the seam near the top right corner of the RAM access door and gently pry the door up slightly.

    • The door is held in place by small clips around its edges. Pry until you feel the nearest clips release.

  4. PC Laptop Batteries

    An easy fix for a big power boost.

    Купить сейчас

    PC Laptop Batteries

    An easy fix for a big power boost.

    Купить сейчас
  5. Insert the wide edge of an opening pick into a new part of the seam between the door and the computer. Pry the door up to release the clips closest to the pick. Continue to slide the pick along the seam all the way around the door, prying as you go, until all the clips holding the door down have been released.
    • Insert the wide edge of an opening pick into a new part of the seam between the door and the computer.

    • Pry the door up to release the clips closest to the pick.

    • Continue to slide the pick along the seam all the way around the door, prying as you go, until all the clips holding the door down have been released.

  6. Remove the RAM access door.
    • Remove the RAM access door.

  7. Remove the four 2.4 mm screws securing the left hard drive with a  Phillips screwdriver. Use the pull-tab to lift the hard drive housing and pull the hard drive away from the connector.
    • Remove the four 2.4 mm screws securing the left hard drive with a Phillips screwdriver.

    • Use the pull-tab to lift the hard drive housing and pull the hard drive away from the connector.

  8. Remove the four 2.4 mm screws securing the right hard drive housing with a  Phillips screwdriver. Use the pull-tab to lift the hard drive housing and pull the hard drive away from the connector. Use the pull-tab to lift the hard drive housing and pull the hard drive away from the connector.
    • Remove the four 2.4 mm screws securing the right hard drive housing with a Phillips screwdriver.

    • Use the pull-tab to lift the hard drive housing and pull the hard drive away from the connector.

Заключение

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

One other person completed this guide.

Kyle Miller

Участник с: 06.10.2016

483 Репутация

Автор 3 руководств

Команда

USF Tampa, Team 2-1, Sullivan Fall 2016 Member of USF Tampa, Team 2-1, Sullivan Fall 2016

USFT-SULLIVAN-F16S2G1

4 членов

Автор 11 руководств

Один комментарий

Dose the Asus ROG G751JL have any m.2 port in there anywhere? And what is the maximum capacity of SSD use in the Asus ROG G751JL?

shohebulalam - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 1

За 7 дней: 30

За 30 дней: 122

За всё время: 2,563