Canon PowerShot SD1000 Flash Unit Replacement

Введение

If your Canon Powershot SD1000 has a broken or faulty flash unit, use this guide to remove and replace it.

A faulty flash unit may have a weak discharge, resulting in a dimly lit photo or failure to discharge entirely.

The flash unit of the Canon Powershot SD1000 is built into the main body of a camera, and will require disassembly of the main body.

Before using this guide, check the function settings of your camera to find what mode the flash is set to. Oftentimes, when set to "Auto," the flash will not discharge.

Выберете то, что вам нужно

Шаг 1 Back Panel

Canon PowerShot SD1000 Flash Unit Replacement, Back Panel: шаг 1, изображение 1 из 2

Canon PowerShot SD1000 Flash Unit Replacement, Back Panel: шаг 1, изображение 2 из 2

Remove the two 2.9 mm screws from the side panel closest to the camera lens.

Редактировать

Шаг 2

Remove the two 2.9 mm screws from the camera bottom panel.

Редактировать

Шаг 3

Remove the two 2.9 mm screws from the side panel farthest from the lens.

Редактировать

Шаг 4

Pull the back panel away from the camera body, starting at the end with the function buttons.

Редактировать

Шаг 5

Remove the small cover panel and the attached wrist strap mount.

Редактировать

Шаг 6 Front Case

Canon PowerShot SD1000 Flash Unit Replacement, Front Case: шаг 6, изображение 1 из 1

Remove the front cover by gently pulling it away from the camera body.

Редактировать

Шаг 7

Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Редактировать

Шаг 8 LCD Screen

Canon PowerShot SD1000 Flash Unit Replacement, LCD Screen: шаг 8, изображение 1 из 1

Remove the two 2.4 mm screws located at the top of the LCD panel.

Редактировать

Шаг 9

Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

Редактировать

Шаг 10

Push the metal frame away from the metal tab using the spudger to detach the frame.
Rotate the metal frame upwards.
The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Редактировать

Шаг 11

Carefully lift the metal frame from the camera.
Remove the black LCD screen, leaving the thin lens pieces in place.
BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

Редактировать

Шаг 12

Canon PowerShot SD1000 Flash Unit Replacement: шаг 12, изображение 3 из 3

Carefully pull on the orange connector ribbon to disconnect the LCD screen.
The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.
Tweezers are helpful to disconnect the ribbon.

Редактировать

Шаг 13 Flash Unit

Canon PowerShot SD1000 Flash Unit Replacement, Flash Unit: шаг 13, изображение 1 из 2

Canon PowerShot SD1000 Flash Unit Replacement, Flash Unit: шаг 13, изображение 2 из 2

Slide the metal frame off of the camera on the side that is closest to the flash mechanism.

Редактировать

Шаг 14

Use a Phillips #00 screwdriver to remove the 2.4 mm screw that secures the flash assembly.

Редактировать

Шаг 15

Use the spudger to gently and carefully disconnect the flash assembly ribbon from the black connector lock.

Редактировать

Шаг 16

Pull the flash assembly forward out of the camera to remove it.
BE CAREFUL when handling the flash assembly. Touching the capacitor (the black cylinder attached to the flash assembly) could shock you.

Редактировать