Перейти к основному содержанию

Введение

Follow this guide to replace the battery on a Sony DualShock 4 CHU-ZCT2U Playstation controller.

This guide will also work for the older CHU-ZCT1U model controller but be sure to order the JDM-030 battery, which has a different sized connector. You can check which model controller you have by referencing the sticker on the rear panel.

If your battery is swollen, take appropriate precautions.

  1. DualShock 4 CHU-ZCT2U Battery Replacement, Remove the rear panel screws: step 1, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement, Remove the rear panel screws: step 1, image 2 of 2
    • Use a Phillips screwdriver to remove the four 6.4 mm-long screws from the rear panel.

  2. DualShock 4 CHU-ZCT2U Battery Replacement, Separate the rear panel: step 2, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement, Separate the rear panel: step 2, image 2 of 2
    • Insert an opening tool into the crease where the front and rear panel meet, starting from the outside edge of either handle.

    • Gently pry the rear panel off of the front panel until they become partially separated.

  3. DualShock 4 CHU-ZCT2U Battery Replacement, Release the plastic clips: step 3, image 1 of 3 DualShock 4 CHU-ZCT2U Battery Replacement, Release the plastic clips: step 3, image 2 of 3 DualShock 4 CHU-ZCT2U Battery Replacement, Release the plastic clips: step 3, image 3 of 3
    • Use the opening tool to separate the panels by releasing the plastic clips around the perimeter of the controller.

  4. DualShock 4 CHU-ZCT2U Battery Replacement, Remove the rear panel: step 4, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement, Remove the rear panel: step 4, image 2 of 2
    • Lift the rear panel directly away from the controller.

    • Do not completely remove the rear panel. It is still attached to the controller by a ribbon cable.

  5. DualShock 4 CHU-ZCT2U Battery Replacement: step 5, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement: step 5, image 2 of 2
    • Use your fingers to gently pull the ribbon cable straight out of its connector on the motherboard.

    • Since this cable's pull tab is too small to grab with fingers or tweezers, grab the cable itself. Otherwise utilize pull tabs whenever possible.

    • During reassembly, grab the ribbon cable by the blue tab and gently press the cable straight into the connector. Push the blue tab rather than the ribbon cable itself.

  6. DualShock 4 CHU-ZCT2U Battery Replacement, Remove the battery: step 6, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement, Remove the battery: step 6, image 2 of 2
    • Use a pair of tweezers to pull the battery's power connector straight up from the motherboard.

  7. DualShock 4 CHU-ZCT2U Battery Replacement: step 7, image 1 of 2 DualShock 4 CHU-ZCT2U Battery Replacement: step 7, image 2 of 2
    • Remove the battery.

Заключение

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

6 участников успешно повторили данное руководство.

Sam Omiotek

Участник с: 25.02.2019

49 710 Репутация

Автор 264 руководств

Team

iFixit Участник iFixit

Community

146 членов

Автор 16 062 руководств

2 Comments

For this DualShock 4 CHU-ZCT2U Battery Replacement, shouldn’t the battery model be JDM-040 and not JDM-030 for this controller. I ordered the battery listed but the connector was too large. So I believe this needs to be edited to match accordingly to avoid confusion and incorrect orders. Thanks!

Tom Nguyen - Ответить

Good catch! I just pulled apart the ZCT1U and ZCT2U models and you are right. I will fix this in the guide. Thank you!

Sam Omiotek -

Добавить комментарий

Просмотр статистики:

За последние 24часов: 21

За последние 7 дней: 110

За последние 30 дней: 535

За всё время: 9,951