Перейти к основному содержанию

Electrolux LTE12 - Washing Machine Disassembly

Выберете то, что вам нужно

  1. Electrolux LTE12 - Washing Machine Disassembly, Electrolux LTE12 - Washing Machine Disassembly: шаг 1, изображение 1 из 2 Electrolux LTE12 - Washing Machine Disassembly, Electrolux LTE12 - Washing Machine Disassembly: шаг 1, изображение 2 из 2
    • Unplug the wall outlet.

    • Release the water hose.

    • Loosen the 4 Phillips screws at the top and 2 1/4 screws below.

  2. Electrolux LTE12 - Washing Machine Disassembly: шаг 2, изображение 1 из 1
    • Fasten the lid of the washing machine with a large crepe tape. Do not open when removing the top of the machine.

    • There is no need to remove the glass cover to remove the top of the machine.

  3. Electrolux LTE12 - Washing Machine Disassembly: шаг 3, изображение 1 из 1
    • Open the top of the washer. Lift the back first. And then the front.

    • Grip the top of the machine with care. Take care not to drop and break the cover glass.

    • Release the power cord and hose clips from the pressure switch.

  4. Electrolux LTE12 - Washing Machine Disassembly: шаг 4, изображение 1 из 1
    • Remove the Phillips screw.

    • Remove the two plastic fasteners.

    • Remove the protective cap (semi-transparent) on the left side.

  5. Electrolux LTE12 - Washing Machine Disassembly: шаг 5, изображение 1 из 1
    • Remove the two Phillips screws.

    • Remove the protective cap (semi-transparent) on the right side.

  6. Electrolux LTE12 - Washing Machine Disassembly: шаг 6, изображение 1 из 1
    • To loosen the Control Panel cover, loosen the two Phillips screws. (Left side).

  7. Electrolux LTE12 - Washing Machine Disassembly: шаг 7, изображение 1 из 1
    • To loosen the Control Panel cover, also loosen the two Phillips screws on the right side.

  8. Electrolux LTE12 - Washing Machine Disassembly: шаг 8, изображение 1 из 1
    • Carefully lift the cover of the Control Panel. In this photo, the glass cover was removed to enlarge the image.

  9. Electrolux LTE12 - Washing Machine Disassembly: шаг 9, изображение 1 из 2 Electrolux LTE12 - Washing Machine Disassembly: шаг 9, изображение 2 из 2
    • If there is a need to replace the Power Circuit Board, carefully pull out the program select button.

    • And then loosen the two Phillips screws.

    • Disconnect the cables carefully.

  10. Electrolux LTE12 - Washing Machine Disassembly: шаг 10, изображение 1 из 2 Electrolux LTE12 - Washing Machine Disassembly: шаг 10, изображение 2 из 2
    • To remove the circuit board from the Panel buttons, remove the three Phillips screws. Disconnect the cable carefully.

    • When removing the circuit board from the buttons, be aware of the three button springs.

  11. Electrolux LTE12 - Washing Machine Disassembly: шаг 11, изображение 1 из 3 Electrolux LTE12 - Washing Machine Disassembly: шаг 11, изображение 2 из 3 Electrolux LTE12 - Washing Machine Disassembly: шаг 11, изображение 3 из 3
    • If you need to replace any components on the button circuit board, loosen the three Phillips screws to remove the acrylic shield.

    • The problem with my machine was the power button. With a soldering iron and a sucker, I switched on the power switch.

  12. Electrolux LTE12 - Washing Machine Disassembly: шаг 12, изображение 1 из 1
    • To change the pressure switch, cut the clamp and remove the

    • Disconnect wires.

    • And then loosen the two Phillips screws.

    • To assemble the Washing Machine, follow the same procedure, in the reverse order.

Заключение

To reassemble your device, Follow these instructions in reverse order.

2 участников успешно повторили данное руководство.

Особая благодарность этим переводчикам:

pt en

100%

irlandaпомогает нам починить мир! Хотите внести свой вклад?
Начните переводить ›

Jose Gustavo Abreu Murta

Участник с: 07/06/10

4 558 Репутация

Автор 9 руководств

3 Комментариев

Ola amigos boa noite. Estou como uma maquina de lavar eletrolux lt12f já troquei a placa de potencia e a de interface, agora ela fica com todos os leds ligados e o buzzer bipando sem parar.

Será que os amigos podem ame ajudar a identificar qual o problema?

Anael Dolesk - Ответить

Anael, reveja todas as conexões e certifique-se que a placa principal é do modelo correto.

Sugiro desconectar os outros cabos e fazer um teste.

Jose Gustavo Abreu Murta - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 3

За последние 7 дней: 27

За последние 30 дней: 90

За всё время: 3,910