Введение

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

  1. Turn off the printer.
    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

    Добавить комментарий

  2. Locate the IEEE cover in  the back.
    • Locate the IEEE cover in the back.

    • Gently slide cover to the right to unlatch then pull to remove it.

    Добавить комментарий

    • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

    • Remove the 6mm screw that holds the rear housing in place.

    Добавить комментарий

    • Remove the rear housing by pulling it backwards.

    Добавить комментарий

    • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion

    • Remove the side housing by pulling it outwards.

    Добавить комментарий

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

    Добавить комментарий

    • Lift the paper support.

    • Open the printer cover and front cover.

    Добавить комментарий

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6mm Phillips #2 screws.

    Добавить комментарий

    • Detach the tabs from the pins on each side by pulling it outwards.

    Добавить комментарий

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

    Добавить комментарий

    • Disconnect the cable on the side by carefully pulling it outwards.

    • You may need to gently rock the cable up and down while pulling.

    Добавить комментарий

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

    Добавить комментарий

    • Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.

    Добавить комментарий

    • Remove the acetate tape that secure the connector cable.

    Добавить комментарий

    • There are six screws that secure the printer mechanism.

    • Using the #2 Phillips screwdriver, remove the three 10mm screws shown.

    Добавить комментарий

    • Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.

    Добавить комментарий

    • Remove printer mechanism from lower housing by holding the handles and lifting it upwards.

    Добавить комментарий

    • Remove the CD-R unit housing by releasing the two attaching points to the tray base.

    • Pull it outwards diagonally one side at a time.

    Добавить комментарий

    • Remove the left frame support plate by removing the two 6mm screws that secure it.

    • Pull it out by hand to free it.

    Добавить комментарий

    • Using the #2 Phillips screwdriver, remove the four 6mm screws.

    • Remove the two 8mm screws.

    • The screws are located on the lower sections of the printer.

    Добавить комментарий

    • Two guide pins secure the paper EJ assy in place.

    • Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.

    Добавить комментарий

    • Remove the paper EJ frame assy by pulling the it towards you.

    Добавить комментарий

Заключение

To reassemble your device, follow these instructions in reverse order.

27 участников успешно повторили данное руководство.

Larry Huang

Участник с: 12.10.2011

704 Репутация

Автор 4 руководств

Команда

Cal Poly, Team 17-11, Regan Fall 2011 Member of Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 членов

Автор 6 руководств

Комментариев: 0

Добавить комментарий

Просмотр статистики:

За 24 часа: 2

За 7 дней: 32

За 30 дней: 124

За всё время: 12,733