Почините Свои Вещи Сообщество Магазин

General Electric Create Jason Wu Power Supply Button Replacement

Введение

If your camera will not power on, one issue could be the power supply button. This guide will demonstrate how to fix this issue.

Выберете то, что вам нужно

  1. General Electric Create Jason Wu Power Supply Button Replacement, General Electric Create Jason Wu Casing Disassembly: шаг 1, изображение 1 из 3 General Electric Create Jason Wu Power Supply Button Replacement, General Electric Create Jason Wu Casing Disassembly: шаг 1, изображение 2 из 3 General Electric Create Jason Wu Power Supply Button Replacement, General Electric Create Jason Wu Casing Disassembly: шаг 1, изображение 3 из 3

    • Begin by removing the 5 screws (located: 2 screws on either side and 1 screw on the bottom) using the PH000 head in the Precision Phillips Screwdriver.

    • These screws were missing in our example. These screws should have been small Phillips PH000 screws 1.5mm in length.

    • These screws are very small. To keep from losing any pieces, place all small metals on a magnetic project mat.

    Редактировать

  2. General Electric Create Jason Wu Power Supply Button Replacement: шаг 2, изображение 1 из 2 General Electric Create Jason Wu Power Supply Button Replacement: шаг 2, изображение 2 из 2

    • After the screws are removed, pull the front casing up and away from the camera.

    • If the casing is difficult to remove, use a plastic opening tool to gently pry up on the front as shown.

    Редактировать

  4. General Electric Create Jason Wu Power Supply Button Replacement: шаг 3, изображение 1 из 3 General Electric Create Jason Wu Power Supply Button Replacement: шаг 3, изображение 2 из 3 General Electric Create Jason Wu Power Supply Button Replacement: шаг 3, изображение 3 из 3

    • Using your hands or an opening tool, pry off the silver frame, taking special care at the top of the camera where the buttons are as it is a little harder to pry off.

    • If the back casing is loose from the camera body, it may be easier to perform step 4 first, then accomplish this step. Proceed as your unit allows.

    Редактировать

  5. General Electric Create Jason Wu Power Supply Button Replacement: шаг 4, изображение 1 из 3 General Electric Create Jason Wu Power Supply Button Replacement: шаг 4, изображение 2 из 3 General Electric Create Jason Wu Power Supply Button Replacement: шаг 4, изображение 3 из 3

    • The last part of the casing to disconnect is the back that houses the LCD screen.

    • The screen is attached by a connection ribbon. Gently pull the casing and screen away from the camera body to disconnect the casing.

    • The LCD screen is held onto the back casing by a small amount of adhesive. This may come loose during this process. Do not worry if they become separated.

    • This plug and the connection ribbon are fragile, try not to tear the connection ribbon when disconnecting.

    Редактировать

  6. General Electric Create Jason Wu Power Supply Button Replacement, Power Supply Button: шаг 5, изображение 1 из 3 General Electric Create Jason Wu Power Supply Button Replacement, Power Supply Button: шаг 5, изображение 2 из 3 General Electric Create Jason Wu Power Supply Button Replacement, Power Supply Button: шаг 5, изображение 3 из 3
    Инструмент, используемый на этом этапе:
    Flathead 3/32" or 2.5 mm Screwdriver
    $5.49
    Купить

    • Locate the metal frame removed from around the camera in step 3.

    • Lay the frame button side down or flat and gently pry the button out of place with the 3.0 flathead bit or a pair of tweezers.

    • This is very brittle plastic so use extreme caution and minimal force.

    • The button is secured to the frame by two small black rods pushed into the white colored portion of the button (see picture).

    Редактировать

  7. General Electric Create Jason Wu Power Supply Button Replacement: шаг 6, изображение 1 из 1

    • The button will pry off easily and shouldn't take much force

    Редактировать
Заключение

To reassemble your device, follow these instructions in reverse order.

Автор

и 3 других участников

Kylan Hennessy

Участник с: 01/23/17

573 Репутация

Автор 5 руководств

Значки: 15

+12 значков

Команда

Eastern Washington University, Team 2-6, Crane Winter 2017 Участник Eastern Washington University, Team 2-6, Crane Winter 2017

EWU-CRANE-W17S2G6

4 членов

Автор 7 руководств

0 Комментариев

Добавить комментарий

Просмотр статистики:

За последние 24часов: 2

За последние 7 дней: 3

За последние 30 дней: 4

За всё время: 171