Перейти к основному содержанию

Отремонтируйте ваше устройство

Обучение ремонту

Запчасти и инструменты

Введение

If your device is unable to hold onto a charge or power on, there may be a problem with its battery. This guide will show you how to replace the battery for the Hannspree Hannspad SN1AT71.

The battery replacement will require soldering. Soldering increases the difficulty of replacing the battery. For soldering assistance, there is a tutorial on the iFixit website.

If your battery is swollen, take appropriate precautions.

The battery can be refurbished, so don’t forget to recycle your battery.

Запчасти

Детали не указаны.

  1. Turn off the device.
    • Turn off the device.

    • Place the tablet screen side up.

    • Make sure the device is turned off to avoid damage.

  2. Use the metal spudger to press an opening between the screen and back cover. Plastic tabs are located on each corner of the back cover.
    • Use the metal spudger to press an opening between the screen and back cover.

    • Plastic tabs are located on each corner of the back cover.

    • Be careful, as the plastic tabs are delicate.

  3. Wedge the plastic opening tool between the screen and the back panel to keep tension constant.
    • Wedge the plastic opening tool between the screen and the back panel to keep tension constant.

  4. Manta Driver Kit

    112 bits for every fix.

    Upgrade Your Toolbox

    Manta Driver Kit

    Upgrade Your Toolbox
  5. Slide the metal spudger around the casing to separate it from the inside of the tablet. Slide the metal spudger around the casing to separate it from the inside of the tablet.
    • Slide the metal spudger around the casing to separate it from the inside of the tablet.

  6. Flip the tablet over so the screen side is down after all the tabs are separated. Remove the back panel by delicately lifting it straight up.
    • Flip the tablet over so the screen side is down after all the tabs are separated.

    • Remove the back panel by delicately lifting it straight up.

  7. Remove the adhesive tape from the power connection cables. Remove the adhesive tape from the power connection cables.
    • Remove the adhesive tape from the power connection cables.

  8. Instructions for desoldering can be found on the iFixit website. The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard. Grab hold of the red wire using the tweezers.
    • Instructions for desoldering can be found on the iFixit website.

    • The soldering iron is hot. It can burn you and it can cause damage to the wires and motherboard.

    • Grab hold of the red wire using the tweezers.

    • Desolder the red wire connection from the motherboard using the tip of the soldering iron.

    • Move the wire connection away from the motherboard.

    • Do not let the red wire connection touch other wires or the motherboard.

  9. Desolder the black wire connection from the motherboard by following the previous step. Desolder the yellow wire connection from the motherboard by following the previous step. When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.
    • Desolder the black wire connection from the motherboard by following the previous step.

    • Desolder the yellow wire connection from the motherboard by following the previous step.

    • When moving the wire connections, do not let the red wire connection touch other wires or the motherboard.

  10. Insert the flat end of the nylon spudger between the battery and the case. The battery is attached to the tablet with an adhesive tape, but should slowly come free. Be careful to not puncture or bend the battery during its removal. If your battery is swollen, take appropriate precautions.
    • Insert the flat end of the nylon spudger between the battery and the case.

    • The battery is attached to the tablet with an adhesive tape, but should slowly come free.

    • Be careful to not puncture or bend the battery during its removal. If your battery is swollen, take appropriate precautions.

Заключение

To reassemble your device, follow these instructions in reverse order.

8 участников успешно повторили данное руководство.

matthew vandeventer

Участник с: 11.03.2015

890 Репутация

Автор 5 руководств

Команда

Colorado Springs, Team 9-4, Panko Spring 2015 Участник Colorado Springs, Team 9-4, Panko Spring 2015

UCCS-PANKO-S15S9G4

3 членов

Автор 10 руководств

Комментариев: 3

Easy to follow,but, can't find a battery anywhere, so really No use

Lawrence Pearce - Ответить

Matthew,

Great job!!

I followed your instructions and no problem

Thanks

Me Eisenhut

Howard Eisenhut - Ответить

Where can I buy a replacement battery?

mwause - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 6

За последние 30 дней: 65

За всё время: 8,306