Перейти к основному содержанию

TackLife GSW01A Pump Assembly Replacement

Выберете то, что вам нужно

  1. TackLife GSW01A Pump Assembly Replacement, Pump: шаг 1, изображение 1 из 2 TackLife GSW01A Pump Assembly Replacement, Pump: шаг 1, изображение 2 из 2
    • Before you begin, be sure that the engine is powered off and is cool to the touch.

    • For safety Do Not make adjustments to your equipment without first disconnecting the spark plug.

    • Disconnect the spark plug by grabbing it and pulling it outwards.

  2. TackLife GSW01A Pump Assembly Replacement: шаг 2, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 2, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 2, изображение 3 из 3
    • Pull the siphon tube apart from connector.

    • Make sure to alleviate the pressure in the pump by squeezing the trigger, acknowledging where the tip is pointed.

    • Try to twist the high-pressure hose off by hand. If too tight, use Vise-Grips or Channellock pliers on the grip to loosen and remove the hose. Careful to maintain a steady grip lest the handle strip.

  3. TackLife GSW01A Pump Assembly Replacement: шаг 3, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 3, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 3, изображение 3 из 3
    • OPTIONAL: Remove handle for tool and hand clearance.

    • To remove the handle, unscrew the orange triangle knobs on both sides. With a firm grip on both sides pull handle apart from pressure washer.

  4. TackLife GSW01A Pump Assembly Replacement: шаг 4, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 4, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 4, изображение 3 из 3
    • Remove the 4 mounting bolts. (M8x20)

    • Use an open-ended or box wrench to loosen the bolts. There is not enough clearance for using a socket wrench.

    • Gently tap with a hammer, while safely holding the wrench in place on the bolt with the other hand to loosen the bolts.

    • Be careful not to strip the heads of bolts.

  5. TackLife GSW01A Pump Assembly Replacement: шаг 5, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 5, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 5, изображение 3 из 3
    • Remove the existing pump from motor shaft.

    • Retrieve the shaft key from the keyway inside the pump if it is not on the motor shaft keyseat.

  6. TackLife GSW01A Pump Assembly Replacement: шаг 6, изображение 1 из 1
    • Clean and lubricate the motor shaft and key.

    • Dirt and grit on shaft can possibly cause damage to the pump over time.

  7. TackLife GSW01A Pump Assembly Replacement: шаг 7, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 7, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 7, изображение 3 из 3
    • Correctly set the shaft key and hold in place while sliding the pump onto the motor shaft.

    • Align the keyway inside the pump with the key and slide the pump onto the motor shaft.

    • If key is not properly set, it could possibly cause damage to the pump or motor shaft.

  8. TackLife GSW01A Pump Assembly Replacement: шаг 8, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 8, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 8, изображение 3 из 3
    • Reinstall the 4 mounting bolts.

    • Rotate the pump so that the hose feeds are properly positioned, and bolt holes are aligned with holes on motor.

  9. TackLife GSW01A Pump Assembly Replacement: шаг 9, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 9, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 9, изображение 3 из 3
    • Reattach the hoses.

    • Reattach handle if removed in earlier steps (OPTIONAL step #3).

  10. TackLife GSW01A Pump Assembly Replacement: шаг 10, изображение 1 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 10, изображение 2 из 3 TackLife GSW01A Pump Assembly Replacement: шаг 10, изображение 3 из 3
    • Screw the orange triangular knobs back on.

    • Reattach the spark plug.

    • Verify all connections are snug tight before operating the pressure washer.

Заключение

To reassemble your device, follow these instructions in reverse order.

3 участников успешно повторили данное руководство.

Mallory A Gullett

Участник с: 06/11/20

249 Репутация

1 руководство автора

Команда

University of Memphis, Team S1-G1, Lane Summer 2020 Участник University of Memphis, Team S1-G1, Lane Summer 2020

UM-LANE-SU20S1G1

5 членов

Автор 1 руководств

2 Комментариев

I'm getting milky oil I want to change pump on my tacklife pressure washer 3200 psi what is a good pump?I cant find OEM pump from the number on pump?What size shaft?

Jason Blood - Ответить

My pump leaks. Do you know of a gasket kit? What type of replacement oil is used thank you

G Barnes - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 7

За последние 30 дней: 38

За всё время: 1,282