Перейти к основному содержанию

Отремонтируйте ваше устройство

Обучение ремонту

Магазин

Введение

The motherboard is the last piece of your speaker you should try replacing if it is not operating properly as it is the most difficult to access.

Запчасти

Детали не указаны.

  1. Turn your speaker upside down and insert the plastic opening tool vertically into the slit in the front cover. Slowly pull the plastic opening tool outward to remove the four clips holding the covering in place. Repeat this process for all four edges of the front cover.
    • Turn your speaker upside down and insert the plastic opening tool vertically into the slit in the front cover.

    • Slowly pull the plastic opening tool outward to remove the four clips holding the covering in place.

    • Repeat this process for all four edges of the front cover.

    Sometimes disassemblers forget that the first time they disassembled the item it didn’t want to give up easily: I didn’t like the forces I was having to apply at all, so I switched to two plastic prying tools per “corner” and one in-between them (total 5, you could use plectrums…) before I was happy the the forces were low enough not to break anything.

    Frank Puranik - Ответить

    the front grill is supposed to be first not the back the back has longer while the front has shorter clip

    Water Bass Tester (Water BT) - Ответить

    There are two Phillips head screws to remove before prying the cover off

    jason - Ответить

    Where in south Africa can I buy jbl charge3 port bay replacement

    Donovan Fransman - Ответить

    There appears to be different versions of the Charge 3. If you find it difficult to pry open a second side the two small screws mentioned by Jason will need to be removed but it also indicates that there will be some additional changes to this tear down that I will try to convey in the comments as well.

    john Ramirez - Ответить

    Sadly I damaged the latches on my charge 3. There was more to it than just prying the front cover up. First, there is a small latch on both sides that you need to push down before pulling the front cover towards you that release the clips holding the front cover in place. Pull only slightly forward because… Second, in the front cover there are 6 circular notches connected to the front cover in tue four corners including the middle corners, you need to squeeze the front cover a little bit gently removing the notches so they dont break (like mine did).

    ralphkeneth_gomz - Ответить

    Definitely had to watch about 10 videos and still couldn’t get it to pop out easily.. Took a look at the first picture in the next step and really took note of where the little hole that lets you through to push down the tab is. Once I took a look at that and combined the techniques I’d seen in some of the videos it finally popped off easily. https://www.youtube.com/watch?v=u7i0_nD9... I only watched the first minute of this video but it helped a good bit if anyone else is having trouble.

    Rowan Darko - Ответить

  2. Pull apart your cover gently from both sides and remove it from the speaker housing.
    • Pull apart your cover gently from both sides and remove it from the speaker housing.

    • The inside of the front cover has holes that must match with their corresponding pins on the speaker housing for proper reassembly.

    • Removing the Front Cover does not affect the waterproof seals of the device. However, removing any further disassembly of your speaker will require removing waterproof seals and gaskets. Your device may no longer be waterproof after these have been altered.

    Include dissembling the plastic cover? cover?

    KanGoon - Ответить

    @KanGoon Yes, on mine it took the removal of 6 (reasonably obvious) screws to remove that. I’ll try to insert a photo when I reassemble…

    Frank Puranik - Ответить

    Very good guide! Pics and descriptions make this easy!

    John G Petko - Ответить

    There is a step missing here. How do you remove the rubber cover that covers the port?

    Phillip Luebke - Ответить

  3. Remove the two 8mm Phillips #1 screws from the tabs. NOTE: There may be only one screw. NOTE: There may be only one screw.
    • Remove the two 8mm Phillips #1 screws from the tabs.

    • NOTE: There may be only one screw.

    If your Charge 3 doesn’t look like the above. Do not do this step YET. Go directly to Step 7 removal of the battery. By doing the battery first it will tell you which radiator to remove and thus no need to remove both.

    NOTE:

    On a newer version of the Charge 3 this image will be very different. you will not find a screw. You will also notice that there are two tabs that if slightly lifted while rotating the radiator counter clockwise the radiator is easily removed. There is also no foam or breakable seal on the newer Charge 3.

    john Ramirez - Ответить

  4. Insert  the plastic opening tools underneath both tabs. Insert  the plastic opening tools underneath both tabs.
    • Insert the plastic opening tools underneath both tabs.

    Beim Modell 2016 geht es noch einfacher: Da ist es ein Bajonett-Verschluss (und nur 1 Schraube im vorigen Schritt). Man muss die Abdeckung nur ein paar Grad gegen den Uhrzeigersinn drehen und kann sie dann einfach abziehen. Schritt 5 und 6 entfallen.

    Franz - Ответить

    I believe this is unnecessary, just turn the passive radiator counter clockwise and pull outward. I tried to use the pry tool and broke a plastic tab.

    Frank Krantz - Ответить

    Tip— when you get to this part lightly tap the edge of the speaker on a hard surface— like you’re tapping a jar before opening it.

    maxthibodeaux - Ответить

    Muchas gracias a todos, me dieron cada uno la guía perfecta.

    Rafael de la Torre Perez - Ответить

  5. Twist and pull open the passive radiator. The left radiator twists off counterclockwise; the right clockwise.
    • Twist and pull open the passive radiator. The left radiator twists off counterclockwise; the right clockwise.

  6. Repeat all previous steps for the other passive radiator. NOTE: only the right radiator needs to be removed for changing the battery.
    • Repeat all previous steps for the other passive radiator.

    • NOTE: only the right radiator needs to be removed for changing the battery.

    right or left…. depends on how you view the Charge 3 i guess. No need to remove both radiators for a newer Charge 3. You can remove the battery cover first…find out what side the battery wires exit the battery compartment and then remove the radiator associated with that same side.

    john Ramirez - Ответить

    Anybody else have major problems trying to twist the radiator back into position after replacing the battery? I’m having trouble getting the screw holes to line up again on the right radiator.

    Chapman Steamer 1 - Ответить

  7. Remove the eight 10mm Phillips #1 screws from around the two front speakers. Remove the eight 10mm Phillips #1 screws from around the two front speakers.
    • Remove the eight 10mm Phillips #1 screws from around the two front speakers.

    Die Frage : Ist ob man irgendwo Ersatz Lautsprecher bekommt ???

    nicowihnaleck - Ответить

    Probier's mal hier, vergleiche aber ganz genau (Seriennummer GG…):

    https://ecommerce.mysav.eu/en/jbl/147-sp...

    VauWeh - Ответить

  8. Pull gently on one of the speakers so it is outside of the housing. Be careful as it is still attached with the wires to the motherboard.
    • Pull gently on one of the speakers so it is outside of the housing. Be careful as it is still attached with the wires to the motherboard.

  9. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart. Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart.
    • Press the small metal tab on the speaker connector with a Phillips #000 screwdriver and gently pull the connector apart.

    Where can l buy those speaker for replacing

    Terrence Terrence - Ответить

    Somebody know where I can buy These speakers ?

    motje - Ответить

  10. Repeat the previous step for the second connector.
    • Repeat the previous step for the second connector.

  11. Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free. Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free.
    • Grab the bundled cable connector that joins the speakers to the motherboard with tweezers. Gently pull the connector free.

  12. Now that the second speaker is disconnected from the motherboard, pull the speaker and wires out of the housing.
    • Now that the second speaker is disconnected from the motherboard, pull the speaker and wires out of the housing.

  13. Remove the six 8mm Phillips #1 screws from the outer battery cover. Peel the outer battery cover away from the speaker housing. Peel the outer battery cover away from the speaker housing.
    • Remove the six 8mm Phillips #1 screws from the outer battery cover.

    • Peel the outer battery cover away from the speaker housing.

    For the newer Charge 3 - there are two silver screws located on the opposite side of the charging ports ….. looking at the first picture above they would be in close proximity to the lower two red circles. However, they placed in horizontally not vertically. Once you remove these two screws you can lift the rubber off.

    Note: The rubber is hinged on the opposite side of the two removed screws by tabs. Be careful when rotating it off not to break the tabs.

    Once the rubber is removed…. you will be able to see the battery compartment. It has several black screws… one of which is wedged between the charging port rubber and the battery cover. You can gently pry up the rubber away to allow you to get a screw driver in to get the middle screw out.

    The battery compartment is water tight and has a seal. You will want to loosen all screws evenly so as not to tear or damage the rubber seal.

    john Ramirez - Ответить

  14. Remove the seven 8mm Phillips #1 screws from interior battery cover. Remove the interior battery cover. Remove the interior battery cover.
    • Remove the seven 8mm Phillips #1 screws from interior battery cover.

    • Remove the interior battery cover.

    The newer Charge 3 will have a solid black cover. Once removed the battery can be easily lifted out with your fingers. It is not taped in.

    Gently lift the battery to determine the radiator that needs to be removed. You can identify it by following the battery wiring. There is a small hole at the bottom of the battery compartment that the battery wires go through. The side with the battery wiring hole is the same side as the radiator that needs to be removed.

    john Ramirez - Ответить

  15. Pull gently to disconnect the bundled cable connector in the side of the speaker. This action will separate the battery from the motherboard. Pull gently to disconnect the bundled cable connector in the side of the speaker. This action will separate the battery from the motherboard.
    • Pull gently to disconnect the bundled cable connector in the side of the speaker. This action will separate the battery from the motherboard.

  16. Pull the battery and battery cable out from their housing.
    • Pull the battery and battery cable out from their housing.

    Where can I find (shop) a battery replacement ?

    erik g5 - Ответить

    yo tambien quiero una bateria donde la cosigo?

    henryovidioquispemamani -

    Does anyone know where I can buy a replacement battery?

    Tissaka Senarath - Ответить

  17. Take out the four  8mm Phillips #1 screws out of the port bay cover. Wedge your plastic opening tool around the port bay to remove it. Wedge your plastic opening tool around the port bay to remove it.
    • Take out the four 8mm Phillips #1 screws out of the port bay cover.

    • Wedge your plastic opening tool around the port bay to remove it.

    and then wiggle it directly (almost radially from the cylinder) out until you see the cables shown in the next step.

    Be careful not to damage the plastic gasket as you pull it out,

    Frank Puranik - Ответить

  18. Disconnect the two bundled cable connector from the port bay. Disconnect the two bundled cable connector from the port bay. Disconnect the two bundled cable connector from the port bay.
    • Disconnect the two bundled cable connector from the port bay.

    there’s not much room to get you fingers in. Again I used prying tools to help me get the two connectors off the PCB

    Frank Puranik - Ответить

    How do i get another port bay

    pjimenez98 - Ответить

  19. Remove the three 8mm Phillips #1 screws from the port bay circuit board. Pull the port bay cover off of the circuit board. Pull the port bay cover off of the circuit board.
    • Remove the three 8mm Phillips #1 screws from the port bay circuit board.

    • Pull the port bay cover off of the circuit board.

    Be careful not to break the 2 plastic lugs you can see just below (on the photo) the 2 screws at the edges

    Frank Puranik - Ответить

  20. Desolder the USB, MicroUSB, or AUX port off of the circuit board. Desolder the USB, MicroUSB, or AUX port off of the circuit board.
    • Desolder the USB, MicroUSB, or AUX port off of the circuit board.

  21. Remove the two  9mm  Phillips #1  screws holding in the sides of the motherboard. Remove the two  9mm  Phillips #1  screws holding in the sides of the motherboard. Remove the two  9mm  Phillips #1  screws holding in the sides of the motherboard.
    • Remove the two 9mm Phillips #1 screws holding in the sides of the motherboard.

  22. Gently pull the bundled cable connector on the motherboard. Gently pull the bundled cable connector on the motherboard.
    • Gently pull the bundled cable connector on the motherboard.

    I lost that cable what to do

    Dynamite Gaming - Ответить

    I lost that cable what to

    Dynamite Gaming - Ответить

  23. Gently pull the golden connector off of the motherboard. Gently pull the golden connector off of the motherboard.
    • Gently pull the golden connector off of the motherboard.

    Buenos días, se me despegó el otro extremo del cable del conector dorado y quisiera que me indiquen en qué lugar se vuelve a conectar. Muchas gracias

    Javier Cristanchi - Ответить

  24. Flip  open the top flap on the two ZIF connectors. Gently pull out the ZIF connector cables with tweezers. Gently pull out the ZIF connector cables with tweezers.
    • Flip open the top flap on the two ZIF connectors.

    • Gently pull out the ZIF connector cables with tweezers.

  25. Slide the motherboard out of the housing.
    • Slide the motherboard out of the housing.

Заключение

To reassemble your device, follow these instructions in reverse order.

3 участников успешно повторили данное руководство.

Sunmin Yoon

Участник с: 30.10.2018

851 Репутация

Автор 2 руководств

Команда

Cal Poly, Team S13-G1, White Fall 2018 Участник Cal Poly, Team S13-G1, White Fall 2018

CPSU-WHITE-F18S13G1

3 членов

Автор 16 руководств

Комментариев: 7

Internation version is different. There are no screws for passive radiotors.

Tr0ll05aur0s 3z - Ответить

You have to twist it. I have to managed to get it open because there is no video on youtube (I can’t find any)

Tr0ll05aur0s 3z -

If that even is Charge 3.

Tr0ll05aur0s 3z -

My JBL charge 3 is not charging …please give me idea to fix ..but it’s working perfectly only

nagendra.shriyan - Ответить

My jbl charge are charging but it won't turn on…… i have tried several times to turn it on but it won't turn…… hoping for solutions……

cire_012881 - Ответить

hello mate! did you find any solution?

baran.florin -

Where can I buy the motherboard?

leong065 - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 18

За последние 7 дней: 131

За последние 30 дней: 484

За всё время: 10,213