Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Power down your Mac mini, disconnect all of the cables, and flip it over.
-
Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.
-
The Jimmy should reach a stop about 3/8" down.
-
-
Этот шаг не переведен. Помогите перевести
-
Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount.
-
-
Этот шаг не переведен. Помогите перевести
-
Once you have the first side free, rotate the Mac mini and start prying up on the front edge.
-
Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.
-
-
Этот шаг не переведен. Помогите перевести
-
You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.
-
-
Этот шаг не переведен. Помогите перевести
-
Keep working around the perimeter, freeing the clips along the final edge.
-
-
Этот шаг не переведен. Помогите перевести
-
Flip the Mac mini back over and lift the top housing off of the lower housing.
-
-
Этот шаг не переведен. Помогите перевести
-
Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the tip of a spudger to slightly lift the left side of the ZIF cable lock up from its socket.
-
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Tweezers$4.99-
Use a pair of tweezers to lift the hard drive thermal sensor cable connector up off its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the recessed Phillips screw near the power button securing the internal frame to the bottom housing.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the recessed Phillips screw near the sleep light securing the internal frame to the bottom housing.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the Phillips screw from the internal frame near the Bluetooth antenna.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the Phillips screw near the audio ports securing the internal frame to the bottom case.
-
-
Этот шаг не переведен. Помогите перевести
-
Gently lift the internal frame up from the bottom housing, minding the AirPort antenna and any other cables that may get caught.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the Bluetooth antenna from the internal frame by pushing up on both sides of the board as close to the center post as possible.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws securing the optical drive to the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the mini 180 degrees and remove the two Phillips screws securing the optical drive to the internal frame on the other side.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws securing the interconnect board to the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to separate the interconnect board from the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single Phillips screw securing the IR board to the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
De-route the IR board and cable through the channel near the hard drive in the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
De-route the IR board and cable through the channel within the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
De-route the IR board and cable through the small plastic clip in the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
Use your fingers to disconnect the IR cable connector from its socket on the interconnect board. Make sure to pull straight out, and to pull on the connector and not the cable.
-
Отменить: Я не выполнил это руководство.
Еще один человек закончил это руководство.