Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Power down your Mac mini, disconnect all of the cables, and flip it over.
-
Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.
-
The Jimmy should reach a stop about 3/8" down.
-
-
Этот шаг не переведен. Помогите перевести
-
Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount.
-
-
Этот шаг не переведен. Помогите перевести
-
Once you have the first side free, rotate the Mac mini and start prying up on the front edge.
-
Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.
-
-
Этот шаг не переведен. Помогите перевести
-
You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.
-
-
Этот шаг не переведен. Помогите перевести
-
Keep working around the perimeter, freeing the clips along the final edge.
-
-
Этот шаг не переведен. Помогите перевести
-
Flip the Mac mini back over and lift the top housing off of the lower housing.
-
-
Этот шаг не переведен. Помогите перевести
-
We will first remove the AirPort antenna, located in the lower left corner of this picture.
-
-
Этот шаг не переведен. Помогите перевести
-
Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.
-
-
Этот шаг не переведен. Помогите перевести
-
Grab the Bluetooth antenna nearest the port side of the computer by the edges of the board and pull it straight up off the internal frame.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the antenna board near the front of the mini by pulling it straight up off the internal frame.
-
If necessary, remove the piece of tape securing the antenna leads to the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to pry the audio ribbon cable connector up off the audio board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following four screws securing the internal frame to the bottom housing:
-
Three 6.7 mm Phillips #00 screws
-
One 9.5 mm Phillips #00 screw
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the internal frame off the bottom housing, starting at the rear edge, until you feel the concealed edge connector on the motherboard disconnect. Then lift straight off, minding the bluetooth and 802.11 antenna cables.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the tip of a spudger to remove the black electrical tape spanning the interconnect board and optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to disconnect the audio ribbon cable from the interconnect board.
-
-
Этот шаг не переведен. Помогите перевести
-
If necessary, remove the yellow kapton tape covering the internal frame and the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws securing the optical drive to the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the mini 180 degrees and remove the two Phillips screws securing the optical drive to the internal frame on the other side.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws securing the interconnect board to the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Insert the flat end of a spudger into the crevice between the optical drive and the interconnect board.
-
Carefully increase the crevice to disconnect the optical drive from the interconnect board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single Phillips screw securing the IR board to the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
De-route the IR board and cable through the opening in the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
De-route the IR board cable from the channel along the internal frame.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to pry the IR board connector up off the interconnect board and remove the IR board from your mini.
-
Отменить: Я не выполнил это руководство.
2 участников успешно повторили данное руководство.