Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Use a coin or spudger to rotate the battery-locking screw 90 degrees clockwise.
-
-
Этот шаг не переведен. Помогите перевести
-
Unscrew the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.
-
-
Этот шаг не переведен. Помогите перевести
-
Grasp the right end of the L-shaped memory cover, then pull it towards you so it clears the battery compartment opening.
-
Lift the memory cover up and out of the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following 3 screws:
-
One 11 mm Phillips#00 in the middle of the lower case. (Head: 5mm dia. x .75mm thick)
-
Two 14.5 mm Phillips #00 (Head: 5mm dia. x .75mm thick)
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
One 3 mm Phillips #0. (Head: 2.75 mm. dia.)
-
Two 4 mm Phillips #0 on the either side. (Head: 2.75mm dia.)
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
Two 6.25 mm Phillips #000. (Head: 4 mm. dia. x .5mm thick)
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the four indicated Phillips screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screws.
-
Four 3.25 mm Phillips #000. (Head: 4 mm. dia. x 4mm thick)
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following 4 screws from the back of the computer:
-
Two 11 mm Phillips #00, with Shank (2.2mm dia. x 2 mm len.) (Head: 3.2 mm. dia. x .5mm thick)
-
Two 7.25 mm Phillips #00, with Shank (2mm dia. x 3.75 mm len.) (Head: 3.2 mm. dia. x .5mm thick)
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws from the optical drive (right) side of the computer:
-
Two 5.2 mm Phillips #00, with shank (2.3mm dia. x 3.25 mm len.) (Head: 3.2 mm. dia. x .5mm thick)
-
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Plastic Cards$2.99-
Use a plastic opening tool, an expired plastic credit, or a similarly-thick card to pry up on the upper case, starting in the upper-left corner and working around to the front of the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
While holding up the upper case, pull up the black tab on the connector end of the silver ribbon cable away from the connector's socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws from the side of the optical drive.
-
Two 3.25 mm Phillips #000 (head: 4 mm. dia. x .3 mm thick)
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the orange optical drive ribbon cable connector from the logic board by prying it straight up using either a finger or a spudger.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the newly revealed display data cable's plug from the logic board by pulling it upward using its black pull-tab.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the newly-revealed hard drive cable's plug from the logic board by pulling it upward using its black tab.
-
-
Этот шаг не переведен. Помогите перевести
-
Peel up the foil tape between the fan and the optical drive. Lift the foil tape from the fan side, leaving it attached to the optical drive.
-
During reassembly, be sure to route the cables beneath the tape before reattaching it.
-
-
Этот шаг не переведен. Помогите перевести
-
Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 2 mm Phillips #00 screw securing the rear corner of the optical drive.
-
The silver-jacketed Bluetooth cable may be covering the screw. If so, carefully push it aside. You may need to remove the screw holding the ground shield lugs for the two nearby cables before you can move the Bluetooth cable aside sufficiently. This screw is 7mm in earlier models, and may be 4.2mm in Santa Rosa/Penryn and 2009 models.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the Bluetooth antenna board from the front edge of the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Deroute the hard drive cable from under the clips along the near side of the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the side of the optical drive closest to you, then slide the drive towards you, and up and out of the computer.
-
First, slide its side nearest to the rear of the Macbook under the edge of the rear frame to the left of the hinge, while also sliding the optical drive's mounting tab at its upper left corner under the cables at this location.
-
Lower the drive partially into the lower housing. Keep the hard drive cable away from the optical drive bay.
-
Before dropping the drive fully in place, use a spudger to push forward (towards the front of the drive) on the screw hole in the drive's mounting tab.
-
Push forward the slider, which runs along the far side of the drive, to insert the end of this slider into a small channel in the lower case's frame. This helps hold the drive in place.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following 4 Phillips screws:
-
Three 3 mm Phillips securing the subwoofer and right speaker to the lower case.
-
One 7.5 mm Phillips securing the loop in the display data cable to the lower case.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the right speaker out of its housing in the lower case.
-
-
Этот шаг не переведен. Помогите перевести
-
Thread the subwoofer and right speaker beneath the display data and microphone cables.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single Phillips screw securing the ground loop in the right speaker cable to the heat sink.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to disconnect the right speaker connector from the logic board.
-
Отменить: Я не выполнил это руководство.
9 участников успешно повторили данное руководство.