Введение

Use this guide to replace a worn-out battery. If your battery is swollen, take appropriate precautions.

Video Overview

  1. Remove the following ten screws:
    • Remove the following ten screws:

    • Three 14.4 mm Phillips #00 screws

    • Three 3.5 mm Phillips #00 screws

    • Four 3.5 mm shouldered Phillips #00 screws

    • When replacing the small screws, align them perpendicular to the slight curvature of the case (they don't go straight down).

  2. Use your fingers to pry the lower case away from the body of the MacBook near the vent. Remove the lower case.
    • Use your fingers to pry the lower case away from the body of the MacBook near the vent.

    • Remove the lower case.

  3. Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board. It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
    • Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.

    • It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.

  4. Free shipping on all orders over 100 $ or containing a Pro Tech Toolkit!

    Посмотрите наш магазин
  5. Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
    • Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

  6. Remove the following two screws:
    • Remove the following two screws:

    • One 5.6 mm Tri-point screw

    • One 13 mm Tri-point screw

  7. Carefully peel the battery warning label off the upper case between the battery and the optical drive.
    • Carefully peel the battery warning label off the upper case between the battery and the optical drive.

    • Do not remove the label from the battery.

  8. Use the attached plastic pull tab to remove the battery from the upper case.
    • Use the attached plastic pull tab to remove the battery from the upper case.

    • If you're installing a new battery, you should calibrate it after installation:

    • Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

    • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook's SMC.

Заключение

To reassemble your device, follow these instructions in reverse order.

418 участников успешно повторили данное руководство.

Комментариев: 30

Is this the same with the Late 2011 model?

JonJon - Ответить

LOL!!! The close-up shots are not of the same woman's hands. The close-up shots have hands with bright yellow fingernail polish. What, they couldn't afford the same woman for close-up shots?!

Stacey Brown - Ответить

LMAO! That's hilarious.

Dave McDowell -

Be careful with the four little "shouldered" screws on the bottom of the case towards the touchpad. They go back in at a slight angle. If you can't get the screws flush with the case, try tilting them a bit before screwing them in.

tim - Ответить

GREAT service! I ordered my new battery on Friday and received it on Monday. The battery is charged at 90%. Im very satisfied

gpabis - Ответить

Просмотр статистики:

За 24 часа: 89

За 7 дней: 644

За 30 дней: 3,102

За всё время: 455,309