Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Remove the following ten screws securing the lower case to the upper case:
-
Seven 3 mm Phillips screws.
-
Three 13.5 mm Phillips screws.
-
-
Этот шаг не переведен. Помогите перевести
-
Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.
-
Remove the lower case and set it aside.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:P6 Pentalobe Screwdriver 2009 15" MacBook Pro Battery$5.49-
Three Pentalobe screws secure the battery to the upper case. They can be removed with this special driver.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two exposed five-point Pentalobe screws along the top edge of the battery.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the tip of a spudger to bend back the finger of the "Warning: Do not remove the battery" sticker while you remove the five-point Pentalobe screw hidden underneath.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the battery by its plastic pull tab and slide it away from the long edge of the upper case.
-
-
Этот шаг не переведен. Помогите перевести
-
Tilt the battery back enough to access the battery cable connector.
-
Pull the battery cable connector away from its socket on the logic board and remove the battery from the upper case.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Hold the end of the cable retainer down with one finger while you use the tip of a spudger to slightly lift the other end and rotate it away from the camera cable connector.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the camera cable by pulling the male end straight away from its socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Peel the camera cable off the adhesive securing it to the optical drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the Bluetooth cable by pulling the male end straight away from its socket.
-
Use the flat end of a spudger to pry the Bluetooth antenna cable from its socket on the board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two 8 mm Phillips screws securing the Bluetooth/camera cable retainer to the upper case.
-
Lift the Bluetooth board/cable retainer assembly out of the upper case.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a spudger to pry the optical drive connector straight up off the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove three 3.5 mm Phillips screws securing the optical drive to the upper case.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the optical drive from its left edge and pull it out of the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Débranchez le connecteur du câble du lecteur optique de celui-ci.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to pry the hard drive/IR sensor cable connector up off the logic board.
-
Peel the hard drive cable up from the channel within the subwoofer and right speaker.
-
-
Этот шаг не переведен. Помогите перевести
-
Using the flat end of a spudger, pry the subwoofer connector straight up off the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following four screws securing the subwoofer and right speaker to the upper case:
-
Two 3.2 mm Phillips screws.
-
One 2.6 mm Phillips screw.
-
One 5 mm Phillips screw.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the subwoofer and right speaker assembly out of the upper case.
-
Отменить: Я не выполнил это руководство.
7 участников успешно повторили данное руководство.