Перейти к основному содержанию

MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement

Выберете то, что вам нужно

  1. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, Lower Case: шаг 1, изображение 1 из 1
    • Remove the following ten screws securing the lower case to the upper case:

    • Seven 3 mm Phillips screws.

    • Three 13.5 mm Phillips screws.

  2. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: шаг 2, изображение 1 из 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: шаг 2, изображение 2 из 2
    • Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.

    • Remove the lower case and set it aside.

  3. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: шаг 3, изображение 1 из 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: шаг 3, изображение 2 из 2
    • Disconnect the Bluetooth cable by pulling the male end straight away from its socket.

    • Pull the connector parallel to the face of the logic board, not straight up.

    • Use the flat end of a spudger to pry the Bluetooth antenna cable from its socket on the board.

  4. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: шаг 4, изображение 1 из 2 MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement: шаг 4, изображение 2 из 2
    • Remove the two 8 mm Phillips screws securing the Bluetooth/camera cable retainer to the upper case.

    • One of the screws may remain captive in the Bluetooth/camera cable ground loop. If replacing the display, be sure to transfer this screw to the new unit.

    • Lift the Bluetooth board/cable retainer assembly out of the upper case.

  5. MacBook Pro 15" Unibody Mid 2009 Bluetooth Board Replacement, (Anti-Glare Option) Bluetooth Board: шаг 5, изображение 1 из 1
    • Remove the single Phillips screw securing the Bluetooth board to the retainer.

    • Lift the Bluetooth board off the retainer.

Заключение

To reassemble your device, follow these instructions in reverse order.

3 участников успешно повторили данное руководство.

4 Комментариев

is there a newer bluetoth 4.0 / 4.1 board available for the mid 2009 15'' model?

roblamper - Ответить

I second roblamper's question... Yosemite/iOS 8's new "Handoff" as well as "OS X+iOS AirDrop" feature(s) appear to be thwarted on the Mid 2009 MBP due to the existing Bluetooth hardware limitation. I suppose even if there is a Bluetooth 4.0 LE replacement available there may be some .kext changes required. Regardless, baby steps... First things first and that is discovering suitable hardware (-;

honDA9xsi - Ответить

Does anyone know where the bluetooth board for a NON ANTI-GLARE model might be found? I'm presuming that I have to lift the logic board to get to it as I can't see anything from the underside.

Hope you can help!

Thanks

John

jpmolesworth - Ответить

Where do i find that Cable?

pkremsi - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 3

За последние 30 дней: 18

За всё время: 17,664