Перейти к основному содержанию

Этот документ имеет более свежие изменения. Перейти к последней непроверенной версии.

Nintendo Switch Rear Panel Replacement

Выберете то, что вам нужно

  1. Nintendo Switch Rear Panel Replacement, Rear Panel: шаг 1, изображение 1 из 1
    • Remove the four 6.3 mm Tri-point Y00 screws from the rear panel.

  2. Nintendo Switch Rear Panel Replacement: шаг 2, изображение 1 из 1
    • Remove the single 6.1 mm Phillips #000 screw from underneath the kickstand.

  3. Nintendo Switch Rear Panel Replacement: шаг 3, изображение 1 из 1
    • Remove the two 2.7 mm Phillips #000 screws from the bottom of the device.

  4. Nintendo Switch Rear Panel Replacement: шаг 4, изображение 1 из 1
    • Remove the single 2.7 mm Phillips #000 screw from the top of the device.

  5. Nintendo Switch Rear Panel Replacement: шаг 5, изображение 1 из 2 Nintendo Switch Rear Panel Replacement: шаг 5, изображение 2 из 2
    • Remove the single 3.8 mm Phillips #000 screw from the right Joy-Con rail.

    • Remove the single 3.8 mm Phillips #000 screw from the left Joy-Con rail.

  6. Nintendo Switch Rear Panel Replacement: шаг 6, изображение 1 из 3 Nintendo Switch Rear Panel Replacement: шаг 6, изображение 2 из 3 Nintendo Switch Rear Panel Replacement: шаг 6, изображение 3 из 3
    • Pull the rear panel up and off of the device.

Заключение

To reassemble your device, follow these instructions in reverse order.

75 участников успешно повторили данное руководство.

Blake Klein

Участник с: 01/29/17

70 528 Репутация

Автор 50 руководств

10 Комментариев

Excellent and concise guide.

The new panel doesn’t come with the sticky grille pieces x 2 on the bottom. Is it supposed to be a straight transfer between the old and the new?

fclbriat123 - Ответить

You can transfer the grill to the new back plat

Phillip Norton -

Just did this replacement and there are a few things to keep in mind that this review does not mention. There are x2 square foam pieces that can be transferred to the new panel located at the bottom backside of the old. Also, the game cartridge shield hardware and the kickstand holder hardware have to be taken off the back of the old panel and transferred to the new panel. The kickstand has 2 Phillips #000 screws and the game cartridge shield has 1 Phillips #000 screw

Ryan Talbert - Ответить

How do you transfer the foam pieces? Use some heat to loosen their adhesive and then remove them and transfer over the new backplate?

John - Ответить

Is the casing the same between the HAC model and the HAD model? This guide doesn’t specify

Julian Webb - Ответить

I am using iFixit Pro tool kit. What to do if one of the 000 screw’s cap appears to be stripped off? How to extract it if perchance?

Dr.Genuks - Ответить

I had trouble removing the outermost screws, I think they’re actually Y00 as opposed to Y00. Not sure if I’m the only one who’s had an easier time with Y000, if they are I’ll update the wiki

Esme Xuan Lim - Ответить

I can’t take out the back screws of my switch with y00 ?

V W - Ответить

Detailed guides like this are so helpful!

Swapped the backplates in less than 20 minutes with no issues. I recommend that you press on the screw firmly and turn slowly. Do this and check as you turn and you shouldn't strip any screws.

Yakarot Sennin - Ответить

I wanted to support ifixit, and was ok with it being over 3x as expensive as Amazon as it's probably better parts ($13 vs $45). But Amazon had next day delivery whereas here standard is 5-10 days and express is 3-5. I really want to support you guys but you've got to be competitive somehow...

Para Celsus - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 57

За последние 7 дней: 323

За последние 30 дней: 1,578

За всё время: 91,633