Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Remove the battery cover from the remote and batteries inside.
-
Unscrew the four visible screws on the remote. These are Y1 tri-point screws.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a tool to gently pry apart the white tabs near the top of the controller.
-
Once you open up the remote, there should now be two separate pieces.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a tool or your fingers to remove the speaker piece from the remote.
-
-
Этот шаг не переведен. Помогите перевести
-
Simply remove the rest of the buttons and the flexible plastic covering.
-
-
Этот шаг не переведен. Помогите перевести
-
Go back to the side of the remote with the motherboard.
-
Gently lift and remove it from the base.
-
-
Этот шаг не переведен. Помогите перевести
-
Find the white tabs facing where the sensor screen was.
-
Place a tool under one tab and push up until both tabs pop out of place, and remove the B trigger.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a tool and place it under the rumble motor. Gently lift and remove it from the plastic housing.
-
-
Этот шаг не переведен. Помогите перевести
-
To remove the plastic housing, you have to locate the two white tabs. Use your thumbs to gently pull them apart and remove the plastic housing.
-
Remove the rubber button from the plastic housing.
-
-
-
Этот шаг не переведен. Помогите перевести
-
You should now have all the pieces detached from the Wii remote.
-
-
Этот шаг не переведен. Помогите перевести
-
Return the the buttons back to their original spot along with the flexible plastic covering on top.
-
-
Этот шаг не переведен. Помогите перевести
-
Place the rubber button under the plastic housing.
-
Align the two white tabs with the two indents on the sides and slide the plastic housing into place.
-
Put back the rumble motor back to its original spot.
-
-
Этот шаг не переведен. Помогите перевести
-
Return the sensor screen to its spot and slide it back into place.
-
-
Этот шаг не переведен. Помогите перевести
-
Place the B trigger back into its spot and click the two white tabs into place.
-
-
Этот шаг не переведен. Помогите перевести
-
Lay the motherboard on top of the back side of the remote and push down gently til in place.
-
-
Этот шаг не переведен. Помогите перевести
-
Lay the side of the remote with the motherboard on top of the side with the buttons.
-
Align the sides and press together until firmly in place.
-
Screw back in the screws.
-
-
Этот шаг не переведен. Помогите перевести
-
there are two small screws that need to be unscrewed on the bottom of the remote.
-
-
Этот шаг не переведен. Помогите перевести
-
Once the screws are removed, you can pop the top off.
-
Next take the thumb stick and very gently take it off.
-
-
Этот шаг не переведен. Помогите перевести
-
The wire that plugs into the actual remote needs to be pulled apart from the whole nunchuk.
-
-
Этот шаг не переведен. Помогите перевести
-
It'll be easier to slide the other piece out to so make sure to gently slide it out.
-
-
Этот шаг не переведен. Помогите перевести
-
Then remove the plastic that connects the sensor and the shoulder buttons.
-
-
Этот шаг не переведен. Помогите перевести
-
Now start to attach all of the pieces back starting with the hard plastic first.
-
Make sure not to force the sensor in the spot and slide it upwards.
-
The shoulder buttons are easy to put in but don't push it.
-
Example of my partner.
-
-
Этот шаг не переведен. Помогите перевести
-
Be careful when putting the wires back in because they are easy to fall out.
-
-
Этот шаг не переведен. Помогите перевести
-
Lastly she easily popped the top back on and screwed the bottom to back on and got it to work as it used to.
-
Отменить: Я не выполнил это руководство.
23 участников успешно повторили данное руководство.
6 Комментариев
Great guide! I took one of my remotes apart some years ago. Now, with fresh tri-wing driver in hand, I am ready to reassemble the thing. Problem: where to solder the green ground? It currently is fused to the nunchuk connector housing, but where does the other end go??? Wish I'd noted that, back then
Hello do you have tutorials for unassembly nunchuck's connector please?
I want to take the springs off the wii Remotes Back. The ones that are still in the back during Step 10.