Перейти к основному содержанию

Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.

Выберете то, что вам нужно

  1. Этот шаг не переведен. Помогите перевести

    : шаг 1, изображение 1 из 1
    • Start by removing the six T2 screws that hold the inner lining of the headset to the front.

    It’s actually 6x T3 screws. A T2 driver is smaller than the groves of the T3 screws, will slip and strip.

    Steven - Ответить

    It may depend on your bit manufacturer. I used an ifixit T2.

    Daniel Yoder - Ответить

    What screw size are these? I need to replace one but I don't know what to search for

    Michele Bright -

    I have T2 on mine as well

    weiwei.e.sun - Ответить

    What if one of the screws strips? We are using a t3 and it got all screws out but one. Now we cannot get that last screw out

    AliD - Ответить

    Not much you can do except drill it out.

    Kmic -

  2. Этот шаг не переведен. Помогите перевести

    : шаг 2, изображение 1 из 2 : шаг 2, изображение 2 из 2
    • One side at a time, insert a pick next to the nosepiece, slide it to the edge and pry.

    • When both sides are loose, carefully lift the cover out, and fold it so that the nose piece is on the outer perimeter of the device, as shown in the second image.

    • The proximity sensor is still connected via a flex cable, so be careful to not rip or crease the cable.

    • Lift the small black clip on the ZIF connecter up, and pull the flex cable out.

    • The cable is lightly adhered to the headset so be careful when removing it.

    • During reassembly, make sure to position the cable correctly. Latching the small black clip back on shouldn't require much force. If you don't connect the cable correctly, the headset's screen may stay black and the device will turn off after a few seconds.

    I’m going to do this in about 2 month and this part seems difficult any tips?

    Someone - Ответить

    Shove your prying tool right in the sides (right and left, where the two arrows pointing inward are) and it pops right out (don't push too fast, just keep pushing until it pops out, i suggest using the flat end of a normal Ifixit spudger)

    Kmic -

    I REALLY wish this step had some better close ups. I thought I connected the cable correctly but I'm getting the black screen silly stuff going on. Boo!

    Infinimitsu - Ответить

    You have to push the connector in a bit, and then the black clip will latch down. I'm using a lighted magnifier, myself.

    Shayne Cameron - Ответить

    Bouta throw this thing across the room trying to open it

    Possum - Ответить

  3. Этот шаг не переведен. Помогите перевести

    : шаг 3, изображение 1 из 1
    • Remove the three P0 screws.

    • Remove the two P0 screws

    • The two orange screws near the top are very deep, a longer head screwdriver may be required

    Does iFixit have a set with a screwdriver for accessing the left top screw shown here? The space there is very narrow.

    S-ed - Ответить

    The correct size for these five screws is P000, not P0.

    Matthew Foreman - Ответить

    where can I look up the naming scheme for that screw size you’r etalking about?

    is that the same as the phillips PH000?

    is that describing the thread dimensions or the head of the screw, or both?

    I’ve looked up the screw dimensions / where I can get spares but can’t seem to find consistent results for this one,

    I want to know the screw’s head and thread measurements so I can recreate a custom oculus shell in CAD and have the proper screws and parts all fit back together properly.

    _latch_key_ -

    The ph screw driver was wrong and I stripped one of the screws thanks a lot ifixit

    gavilanesadan@yahoo.com - Ответить

    Of note; the screws are PH000 and they are especially soft and easy to strip.

    Alexander Owen - Ответить

    For those like me that do not have the Marlin screwdrivers or any other thin extension to reach the two deep screws, but if you do have an iFixit kit with bits: I used the normal PH00 bit and the 4mm nut driver as a DIY extension. However, they do not magnetize so this may require some extra finesse to ensure they don't fall apart.

    MINK - Ответить

    The ifixit kit comes with several ph sizes. There is ph000 ph00 and ph0 among others. It is printed on the side of the bits. They are definitely ph0 screws. The regular screwdriver in the ifixit kit can’t reach the two top screws. You will need an extension.

    Brian Krygier - Ответить

    it is PH00 screws for sure, I tried with the PH0 bit from iFixit kit and it does NOT fit

    iampi - Ответить

    I tried the screw bit that yall told me to use, but one of the screws got stripped. How can i remove it?

    lastunio - Ответить

  4. Этот шаг не переведен. Помогите перевести

    : шаг 4, изображение 1 из 2 : шаг 4, изображение 2 из 2
    • Insert a pick and pry at these four spots to release the clips.

    • Lift the front cover away from the headset.

    I found it best just to gently pull it off from the side with my finger nails. There is nothing connected to this cover, yet be careful enough not to break the plastic clips.

    Padraic Hoselton - Ответить

    I don’t need to go to any further steps because I’m only replacing the front shell but still it is a good thing I found out about this tutorial or else I would be a mess right now

    Someone - Ответить

  5. Этот шаг не переведен. Помогите перевести

    : шаг 5, изображение 1 из 3 : шаг 5, изображение 2 из 3 : шаг 5, изображение 3 из 3
    • Unplug the side WiFi antenna.

    • Remove the single P0 screw

    • Remove the two P0 screws

    • Unplug the battery.

    • Remember to put part of the battery ribbon cable under the logic board when reassembling.

    After I remove bracket I found that battery cable already disconnected.After connect it my problem of quest 2 not charge after drop is fix. Thank you for helpful guide.

    Korakot Ano - Ответить

    If the problem of it not charging persists it is a motherboard issue

    Kmic -

    Do you have the lengths for these color codes? I sorted mine but the cat knocked the bin over mixing the screws, most I remember. The bt antenna and the front housing screws are all I have left to sort

    bilmenendez - Ответить

    Same thing happened to me, I unplugged my battery wire and put it back on and now it's working. If you dropped your headset as well, this would probably help

    Luis Benitez - Ответить

  6. Этот шаг не переведен. Помогите перевести

    : шаг 6, изображение 1 из 1
    • Unplug the Bluetooth antenna.

    • 2x P0 screws

    • 4x P0 screws

    • 2x P0 screws—these are longer than the other screws.

    • Lift the antenna away from the headset.

    Note the inner and outer yellow screws are different sizes.

    Steve Mackie - Ответить

  7. Этот шаг не переведен. Помогите перевести

    : шаг 7, изображение 1 из 2 : шаг 7, изображение 2 из 2
    • Unplug the fan.

    • 1x T2 screw

    • 1x P0 screw

    • Lift the front LED away from the headset.

    • Lift the fan away from the headset.

    Holas, quien me dice que es la parte negra del centro de las gafas, que es como una cinta negra grande

    Jhon Hoyos - Ответить

  8. Этот шаг не переведен. Помогите перевести

    : шаг 8, изображение 1 из 1
    • 4x P0 screws

    • Remove the heatsink.

    Do I have to remove this if I am only planning to clean debris off the inside of the eye cups / lens?

    Rod Gonzales - Ответить

    Yes, if you are trying to get inside the lenses you have to remove everything.

    Kmic -

  9. Этот шаг не переведен. Помогите перевести

    : шаг 9, изображение 1 из 1
    • Unplug the side WiFi antenna connector.

    • Unplug the cable leading to the USB Type-C port and headphone jack.

    • Lift and unplug the cables leading to the speakers.

    • Unlatch and remove the cables leading to the top cameras, power button and status LED, bottom cameras, microphones, and volume rocker.

    • Unplug the cables connecting the bottom cameras.

    • Unlatch and remove the cables leading to the front LED and IPD sensor, and proximity sensor.

    • Unplug the cable leading to the screen.

    Does anyone know where I could get a replacement camera. one of my quest 2 cams is shattered due to a fall :)

    Christopher elsas - Ответить

    at aliexpress you can get all the parts

    Kaha -

    Dónde puedo comprar el Flex de una de las cámaras superiores

    Jhon Hoyos - Ответить

    At the "unplug speaker cables" instruction I ripped off the connector from the board by accident. Please add a note that you need to pull it from the sides. The connector seems very fragile.

    NikZapp - Ответить

    I did the exact same. Pretty upset, these instructions lack detail, I'm going jump the wires to the other side. It will just be one side audio to both sides

    Zachary Screeton -

    How do I go about unplugging the yellow arrow ones?

    Jace Gutierrez - Ответить

    Just use the tip of your prying tool and pull up

    Kmic -

  10. Этот шаг не переведен. Помогите перевести

    : шаг 10, изображение 1 из 1
    • 1x 3.5mm hex screw

    • 4x P0 screws

    • Remove the mainboard.

  11. Этот шаг не переведен. Помогите перевести

    : шаг 11, изображение 1 из 2 : шаг 11, изображение 2 из 2
    • Close up on the mainboard.

    Any chance to list all chips on board?

    ksazazel - Ответить

    it looks like there is a 64gb sandisk chip that might come off with some hot air :)

    (but this board look completely different than the quest 2 boards offered on eBay....)

    nitrous dude - Ответить

    I don't know exactly but when I replaced my board this is what it looked like

    Kmic - Ответить

  12. Этот шаг не переведен. Помогите перевести

    : шаг 12, изображение 1 из 3 : шаг 12, изображение 2 из 3 : шаг 12, изображение 3 из 3
    • 2x P0 screws

    • 2x P0 screws

    • Unroute the side WiFi antenna.

    • Lift the midframe away from the case.

    On the upper right hand side of this image next to the first WiFi antenna you unplug, there is a ribbon cable that is held down with a STRONG adhesive that is very difficult to get off. I had to heat up the plastic tool I was using and the cable itself to soften it enough to pull of. Be very careful with it.

    Gavin Alton - Ответить

    There is a metal plate glued to the bottom of the cable. It is easier to get a tool under the metal plate and separate it from the midframe than to unglue the cable from the plate. prying against the plate provides some protection for the cable.

    Ben Klopfenstein -

  13. Этот шаг не переведен. Помогите перевести

    : шаг 13, изображение 1 из 2 : шаг 13, изображение 2 из 2
    • 4x P0 screws hold the battery in the case.

    • 3x T2 screws secure the battery cover.

    • The Quest 2 has a battery life of 2.5 hours, drawing an average of 5.6W.

    What type are the batteries

    And where can i buy the.

    Edo - Ответить

    بحتاج مثل هذه البطارية خاصة لنظارات الواقع الافتراضي ؟وكم السعر؟

    واين يمكنني شراؤها؟

    KaKz alrubyi - Ответить

    You can buy this battery on a website called fix my oculus, يمكنك شراء هذه البطارية على موقع ويب يسمى Fix my oculus

    Kmic - Ответить

  14. Этот шаг не переведен. Помогите перевести

    : шаг 14, изображение 1 из 1
    • Four P0 screws hold part of the retaining plastics on each arm/speaker.

    • Remove the four metal clips on each arm/speaker.

    • The plastics holding the arms on can be removed/twisted off, releasing the arms from the rest of the case.

    Can someone please elaborate on how to remove the metal clips on the arms/speakers?

    Is there a special tool or technique?

    Fixxif - Ответить

    Same here. I can’t figure out how to remove the clips.

    Colin Harris - Ответить

    I would like to know how too! I need to replace my speaker but i doesn't find the technic for metal clip. Thank you

    Patrick Potvin - Ответить

    its easy enough to use tweezers to remove the clips.

    Ben Klopfenstein - Ответить

    I am having trouble removing the screws. Any tips how to get them out.

    AJ Sandoval - Ответить

  15. Этот шаг не переведен. Помогите перевести

    : шаг 15, изображение 1 из 3 : шаг 15, изображение 2 из 3 : шаг 15, изображение 3 из 3
    • Small metal tabs hold the guide rails that the lenses slide on. Removing the rails reveals the display.

    • There is a protective sheet of plastic over the screen. Be careful of dust and scratches.

    What do the screens look like under the lenses? How and where do the cables transmitting the image and power to the screens?

    radgesaidor - Ответить

    Can you add a bit of information about the charging port. I need to replace but not sure best way to access.

    Catherine Kendrick - Ответить

    You have to remove the assembly from the shell first, i.e. everything up to step 12.

    After that you have 4 screws to pull out, 2 of which also hold in the speaker assembly.

    Jheremya Kinsel -

Финишная черта

116 участников успешно повторили данное руководство.

sctanf

Участник с: 01/11/21

2 535 Репутация

1 руководство автора

79 Комментариев

Thank you so much to me for making this guide. Helped me a lot!

It is worth emphasizing that this device has 2! WIFI antennas.

Anyone who wants to disconnect WIFI from their device must disconnect both.

Their connection to the motherboard, is right next to each other, but the right connection is immediately revealed while the left connection next to it is hidden under the black cover and requires a number of additional disassembly steps.

Alternatively, anyone who wants to disconnect WIFI from their device can disconnect the wires in the area where they connect to the antenna stickers on the right and left sides of the eyepieces of the glasses, thus saving all the disassembly of the front cover.

שמחה גרשון בורר - Ответить

Thanks!! this really helped me, I have already customized mine with an official custom filter, but this will add an additional layer of Kashrus.

Leib Felberbaum -

If you just need to replace a camera… it’s 14 screws. You need a T2 and a PH0 (not a P0…) Pretty easy once you get the front cover off and not covered here. It’s pretty easy to see what you do once you get in there though. Good luck!

Chris Madson - Ответить

PH0 and P0 are the same :)

Lylo -

Bravo pour ces informations. Un grand merci

Guidemann Christophe - Ответить

где запчасти то покупать на данное устройство. выломали порт usb, а заменить нечем.

Alexandr Freelan - Ответить

вы можете купить это на FixMyOculus.com

Kmic -

Un grand merci pour ce tuto qui m’a permis de sauver mon casque suite à une grande rasade de vin blanc .

Gérard leroy

gerardleroy78480 - Ответить

This guide is overall great however just as some feedback some of the clour lables are not taged to anything as well as it would be great to see some images of where the battery is located as well as how to get it out.

Pwarrow88 - Ответить

Where is the hard drive located? Is it possible to upgrade the hard drive if you disassemble it far enough?

Ben Stout - Ответить

Can’t say for sure, but it’s VERY likely that the SSD is soldered to the main board and not replaceable without considerable skill and expensive tools

matthew wallace -

The storage device is the large flash chip on the main board labeled “SanDisk.” It is not user-upgradable (well, without considerable effort and maybe a little software hacking).

Aidan Lawrence -

I’m trying to replace the Aux/power port on the mid frame part on the oculus, is it necessary to remove the mainboard in order to gain access to the part I’m trying to replace?

Rizal Antipuesto - Ответить

I’m wondering if you had any luck with this as the brand new headset I got was damaged over Christmas and now the charge port is incredibly loose.

Ryan Hill -

Yes, the port is hidden by the lense/screen assembly

Kmic -

Has anyone confirmed whether or not the Quest 2 has an internal SD card reader? Someone on Facebook claims there is one, but I can’t find anything online that backs it up.

William Cousert - Ответить

Is a full disassembly necessary to remove the lens assembly, or is it simple as just removing the rear cover and swapping it out?

Colten - Ответить

Thank you for this guide, I would like to replace the microphone with an output from a hardware vocoder would this be possible?

Joao Lee - Ответить

how would go about getting to the power button If I just want see if it’s not damaged because that is the only problem I am having. Is to turn it on

Brandxn - Ответить

Need more detail on how to the clip of the first proximity sensor is removed/replaced.

Anthony Rossi - Ответить

oh. nice article rellyy hlpdddesbdyf rgoofnv thought hhbdj cbbjhnnsndvxc

Soren Nordgren - Ответить

any idea where can i get replacement parts?

laz - Ответить

ebay or fixmyouclus.com, Aliexpress too

Kmic -

what is the weight of battery? it's possibile turn on without battery but with cable connected? i think the best solution for future quest it's battery swapping.

patrikmeneguot - Ответить

Battery weight is 63g - I tested and you are not able to use the quest 2 with the battery removed and a power cable connected. The meta logo will appear for ~.1 seconds, then a battery with a slash through it image will appear on the screen.

d__g -

Agradezco mucho la información es una gran ayuda ya que tengo que desarmar totalmente el aparato que es de mi sobrino y lo dejo en el suelo y se le metieron hormigas sin está ayuda no creo haber podido hacerlo gracias

warner bermudez - Ответить

Hay in step 2 removing the rear cover I accidentally cut the ribbon connecting to the rear cover (proximity ribbon) does any1 know where I can get a replacement?

Jerrett Luedy - Ответить

Id try eBay to find a used one as i doubt if Oculus, Facebook or Meta will just sell you the part outright!

Matthew Reed -

So far so good waiting for my replacement screen dam hope for my girls sake i get it back together .hate to file a missing person report.

April Webb - Ответить

Do I need to remove everything to replace the lens and LCD?

David Tompsett - Ответить

The LCD screen shouldn't need changing just change the lens. But if you need both just by a new unit as the Lens is about $80 and the LCD is about the same so for the cost of the parts its probably just easier to buy new!

Matthew Reed -

Is it possible to remove the lenses on early stages?

ozan uygan - Ответить

No you have to remove the screen assembly

Kmic -

I just swapped the mainboard into a new headset piece (speakers power button etc) and the unit works for about 2 minutes and then goes to a black screen. I can hit the power button again and get the device to display three dots, then the screen goes dark again.

Anyone have any ideas? This repair went very smoothly so Im not sure if its overheating now or what.... I did try disabling the prox sensor as well and that did not help.

Chase Gober - Ответить

Probably needed to replace the thermal past that was compromised when your disassembled it.

larstaylor -

You Might have damaged your proximity sensor ribbon cable or connector as it wont work if it cannot detect if its on your face or not. Disabling the prox sensor will for SURE cause that error 100%! It cannot be disabled. That's why I think its the prox sensor ribbon cable or a bad connector that the cable goes into. Try replacing both the sensor and its connector ribbon cable if thats thats possible.

Matthew Reed -

Hi has anyone try swapping a 64gb mainboard for a 128 gb or 256gb to increase the storage?

Dimase - Ответить

I did and it worked great, but the teardown to swap the board is tedious and very very delicate work!!

Matthew Reed -

I don’t know why people are praising this guide. It is terrible, incomplete. Lacks detail. Hand waives critical steps and instructions.

It is a terrible guide, one of the worst on this site.

I have been trying to figure out how to “life the front led away from the headset” for two hours. Each gentle attempt risks destroying it. Worst and most clear instruction I have ever seen.

And that is after trying to deduce what the OP meant multiple times, each with an intuitive leap of faith; rather than clear instructions.

larstaylor - Ответить

if you are still trying a year later, the front LED is held to the fan assembly with some adhesive below the LED, you can just either pull it off or use a pry tool to get it off

Coliflower185 -

It would have been nice of the OP had mentioned that you don’t need to take the %#*@ motherboard and heat sink off to dissemble the main body.

And mentioned that you will need to have thermal paste available to replace the thermal paste you ruined by removing a motherboard and heat sink you’d hit even need to remove.

larstaylor - Ответить

Does replacing the mainboard is plug and play ?

Do i need to do something on the software side to get it to work ?

Asking before ordering part , answer will be very appreciated.

Kobi - Ответить

Yes you can swap motherboards! I did it in mine to get better memory, but if you have a warranty I wouldn't recommend it as this will void your warranty! I replaced my motherboard from a 64GB board to a 128GB one, the Oculus unit booted right up easily, then it gets its updates over the internet so just connect it to your wifi and it will update itself to the newest latest automatically! Now the teardown is tedious and if your not good with electronics I wouldn't attempt it!! As its very easy to damage things!

Matthew Reed -

Hello. After replacing the motherboard, how to pair the old controllers?

Roman Doga -

Definitely one of the most unnecessarily complex devices I've ever disassembled.

Ended up having to take apart everything just to replace that one fried USB port, even accidentally snapped off the latches from two ribbon cable ports in the process (though the latter is entirely my fault in handling teeny tiny pieces).

But at least my Quest 2 is no longer a paperweight now. Thanks OP.

muhdizrin - Ответить

Can You help me? I try to reject the wifi modules and bluetooth modules but ı dont know which one is the wifi and which one is the bluetooth. Thank you for help.

Ahmet Hakan Yıldırım - Ответить

The wifi is in on the top right of the motherboard (pic 5) and the bluetooth antenna is required for it to work, but is attached to the black piece at the bottom (pic 6)

Kmic -

Where is wifi chip? Can I remove it? if I success to remove it, quest 2 works well without wifi?

Antti Silvast - Ответить

Just buy a whole new mainboard, ebay is selling the mainboards really cheap!! Just swap mainboards its easy, but make sure you unpair and factory reset your oculus before you do so, then when you pair the new board to your account its as easy as pie!

Matthew Reed -

Mainboard image must be fake as SK Hynix doesn't make the Qualcomm Snapdragon CPU for the Oculus Quest 2, where the heck did that image come from??

Matthew Reed - Ответить

Hi someone got over excited and dropped my quest now it works for approximately 5 min then the left screen turns off...can this be fixed?

TIA

Si

Jubehasit - Ответить

Sounds like it needs a new screen.

Kmic -

Hola a todos, tengo un problema con mis oculus, no me funciona el Wifi y lo reinicié con los parametros de fabrica pero ahora no puedo completar las opciones de inicio del sistema, hay alguna forma de saltarse la configuración de Wifi ???????

Sergio Salazar - Ответить

Where would I buy a replacement fan and heatsink

Tyler Smith - Ответить

Ebay or a website called fix my oculus

Kmic -

Hola a todos, de casualidad alguno sabe dónde comprar el Flex que va a uno de los sensores superiores de las Oculus quest 2

Jhon Hoyos - Ответить

Where the heck do I buy a Oculus 2 headset battery in Australia?? I have been looking & can't find anything like it???

suewatson939 - Ответить

Does anyone have any idea how far into the disassembly is necessary to just do a shell swap? The speaker arms are damaged on both sides and it sounds like a shell swap would be easier than replacing the arms.

Headset Shell Frame

Rygel Fievel - Ответить

You have to remove everything, sorry.

Kmic -

Has anyone had to replace a broken speaker arm/headband.

carrollshepard - Ответить

Something worth noting for anyone doing this is first time many of the cables will be held down with adhesive tape, so you will need to remove the tape before some of the steps, mainly removing the midframe.

also my quest didn't have the 3.5mm hex screw for the motherboard in it for some reason.

Coliflower185 - Ответить

The left lens on my headset completely stopped working recently. It used to turn back on if I slapped my headset but that has since stopped working. I would assume that it is either a faulty or loose connection to something, but I don't know for sure. How would I go about checking/possible fixing something like that?

Beegeeloo - Ответить

It needs a new screen altogether

Kmic -

Any idea why one would stay white with blue lines in on the screen

Brittany Lemons - Ответить

It means that the screen is broken.

Kmic -

Savez-vous si le port USB peut être changé ? Le mien a grillé. Le casque fonctionne, mais je ne parviens pas à recharger.

Christian Bredin - Ответить

Oui, vous pouvez changer le port USB-C, mais cela demande beaucoup de travail

Kmic -

Danke fürs Zeigen.

Mich würde interessieren, ob man die beiden Objektive so montieren kann, dass der Augenabstand nicht symetrisch ist. Eines meiner Augen ist 3,5mm weiter vom Zentrum als das andere Auge.

Gruß

Martin

Martin - Ответить

Es gibt nur drei Anpassungen für die Augen, ohne das Oculus zu verändern, ist das nicht möglich.

Kmic -

Has anyone an idea where to get a spare battery?

Hornbrille - Ответить

You can find one on ebay or there is a website called fix my oculus

Kmic -

used this to mod a vent hole in the front. guide helps quite a lot! thank you!

test subject - Ответить

If i wanted to swap the headset shell can i remove the entire assembly or do i remove everything bit by bit. Thanks.

Roland Long - Ответить

Everything comes out a little bit at a time because of cables. Hope this helps

Kmic -

I accidentally unplug the 3rd sensor! Where do I plug it back it at ????????? And do I need a special cord to charge it? I bought it off a friend of some sort but I cant get it to charge or turn on either they ripped me off or I have the wrong cord please help

Richie - Ответить

Considering it can't charge (I had the same problem) it needs a motherboard replacement. You don't need a specific cord to charge it, but i recommend the one that comes with the headset. As for the sensor is it the top left, top right, bottom left, or bottom right?

Kmic -

I have black screen when turn on it, and I can reboot, and do factory reset but the black screen still. I don´t know if is the proximity sensor. Any idea?

Emanuel Alejandro JG - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 158

За последние 7 дней: 1,280

За последние 30 дней: 5,957

За всё время: 199,763