Введение

Fixing the lens apparatus on your camera.

Запчасти

Никакие детали не требуются.

Slide the lock into the unlock position.In this case you would need to slide the lock to the right.
  • Slide the lock into the unlock position.In this case you would need to slide the lock to the right.

  • Use your finger to slide battery hatch towards the arrow sign.

  • Both battery and memory card should now be visible.

Добавить комментарий

Open battery hatch and the black cover to expose the battery compartment.
  • Open battery hatch and the black cover to expose the battery compartment.

  • The camera used to create these repair guides did not have a battery and memory card.

  • Pull the battery out and replace with a new one.

  • When putting the battery back in, make sure it is in the same orientation as before.

  • Close the battery compartment and make sure the lock is in the locked position.

Добавить комментарий

Remove the two 2.8 mm Phillips screws as shown in picture.
  • Remove the two 2.8 mm Phillips screws as shown in picture.

Добавить комментарий

Using a Philips Screw Driver, remove the three 2.8 mm Phillips screws on the bottom of the camera as shown in picture.
  • Using a Philips Screw Driver, remove the three 2.8 mm Phillips screws on the bottom of the camera as shown in picture.

Добавить комментарий

Remove the two 2.8 mm Phillips screws on the side of the camera as shown in picture. /state that a screwdriver is needed in the  step.
  • Remove the two 2.8 mm Phillips screws on the side of the camera as shown in picture. /state that a screwdriver is needed in the step.

Добавить комментарий

Use a Spudger tool to pry open case from all sides./No edits necessary Use a Spudger tool to pry open case from all sides./No edits necessary
  • Use a Spudger tool to pry open case from all sides./No edits necessary

Добавить комментарий

Beware of yellow film strip when opening./Caution: Beware of the yellow film strip when opening  the casing of the camera, make this caution notice a different color. Use your fingers to carefully pry off the back casing from the camera assembly/. No edits necessary.
  • Beware of yellow film strip when opening./Caution: Beware of the yellow film strip when opening the casing of the camera, make this caution notice a different color.

  • Use your fingers to carefully pry off the back casing from the camera assembly/. No edits necessary.

Добавить комментарий

Lay the camera on its front side./combine this sentence to the step below.
  • Lay the camera on its front side./combine this sentence to the step below.

  • Use Spudger tool to open the film strip locking mechanism and remove strip./No edits necessary.

  • Hold down on the camera's metal casing with one hand. Using your other hand, completely lift the back case off the rest of the camera, making sure the film strip separates./Make a picture for this step.

Добавить комментарий

Remove the two remaining 2.8 mm Phillips screws on the bottom of the camera.
  • Remove the two remaining 2.8 mm Phillips screws on the bottom of the camera.

  • The other three screws shown in picture were removed to take off the back case.

Добавить комментарий

Using Spudger tool, pry the front case from the camera's components. Use your fingers to carefully pull the back case from the front case. Cut the black and red wires connecting front case to the body of the camera.
  • Using Spudger tool, pry the front case from the camera's components.

  • Use your fingers to carefully pull the back case from the front case.

  • Cut the black and red wires connecting front case to the body of the camera.

  • Being careful nothing get's caught, separate the front case from the camera.

  • To put the new front case back on, solder the wires of the new front case to the components of the camera.

Добавить комментарий

Check the "V" shaped spring to see if it is connected at shown location.
  • Check the "V" shaped spring to see if it is connected at shown location.

Добавить комментарий

Manually move the Lens Apparatus from the inside to shown position.
  • Manually move the Lens Apparatus from the inside to shown position.

  • Check to see if the spring is aligned correctly and lens opens.

  • If not, you will need to take out the spring and place it into the proper position, or get a new spring all together.

  • To reassemble your device, follow these instructions in reverse order.

Добавить комментарий

Заключение

To reassemble your device, follow these instructions in reverse order.

One other person completed this guide.

Alex Penman

Участник с: 28.01.2011

463 Репутация

Автор 4 руководств

Команда

Cal Poly, Team 7-35, Regan Winter 2011 Member of Cal Poly, Team 7-35, Regan Winter 2011

CPSU-REGAN-W11S7G35

4 членов

Автор 5 руководств

Комментариев: 0

Добавить комментарий

Просмотр статистики:

За 24 часа: 0

За 7 дней: 0

За 30 дней: 0

За всё время: 1,164