Перейти к основному содержанию

Philips SBA1060 Capacitor Replacement

Выберете то, что вам нужно

  1. Philips SBA1060 Capacitor Replacement, Battery Casing: шаг 1, изображение 1 из 1
    • Remove the back cover by sliding it off.

    • Remove the 3 AAA batteries.

  2. Philips SBA1060 Capacitor Replacement: шаг 2, изображение 1 из 3 Philips SBA1060 Capacitor Replacement: шаг 2, изображение 2 из 3 Philips SBA1060 Capacitor Replacement: шаг 2, изображение 3 из 3
    • Unscrew the nine exterior screws on the back panel using a PH0-size Philips-head screwdriver.

    • A larger screwdriver head and more force may be required for damaged screws.

    • Remove the triangular end piece by pulling it straight off.

  3. Philips SBA1060 Capacitor Replacement: шаг 3, изображение 1 из 2 Philips SBA1060 Capacitor Replacement: шаг 3, изображение 2 из 2
    • Remove the colored grill by sliding it off in the direction of the removed end piece.

    • Pry off the back battery panel with the plastic opening tool.

    • Be careful to avoid tearing any wires.

  4. Philips SBA1060 Capacitor Replacement, Capacitor: шаг 4, изображение 1 из 1
    • Remove the two screws on opposite ends of the circuit board with the PH0 size philips head screw driver.

    • Slowly pull the circuit board out of the device

    • NOTE: Be careful not to damage any of the wires protruding from the back of the circuit board.

  5. Philips SBA1060 Capacitor Replacement: шаг 5, изображение 1 из 2 Philips SBA1060 Capacitor Replacement: шаг 5, изображение 2 из 2
    • Flip the device and remove the battery plug from the circuit board by pulling out the plugs to fully remove back panel.

    • Remove the speaker plugs from the circuit board by pulling out the plugs. They are located on opposite sides of the circuit board.

    • NOTE: When reassembling, note that the speaker with the red wire goes to the red plug, and the speaker with the white wire goes to the adjacent white plug.

    • Remove the light plug from the circuit board.

    • NOTE: This plug is twice as wide as the speaker and battery plugs.

  6. Philips SBA1060 Capacitor Replacement: шаг 6, изображение 1 из 2 Philips SBA1060 Capacitor Replacement: шаг 6, изображение 2 из 2
    • Locate the capacitor and carefully slide it out of the circuit board.

    • NOTE: The capacitor will be a cylindrical object protruding vertically near the center of the circuit board.

    • Slide the prongs of the replacement capacitor into the two holes of the circuit board where the original capacitor was removed from.

    • Reassemble the speaker.

Заключение

To reassemble your device, follow these instructions in reverse order.

April Driscoll

Участник с: 10/21/13

321 Репутация

Автор 3 руководств

Команда

Clemson, Team 14-4, Benson Fall 2013 Участник Clemson, Team 14-4, Benson Fall 2013

CLEM-BENSON-F13S14G4

3 членов

Автор 4 руководств

0 Комментариев

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 0

За последние 30 дней: 1

За всё время: 725