Введение
Use this guide to replace your heat sink. It is essential to apply a new layer of thermal paste during reassembly.
Выберете то, что вам нужно
-
-
Turn the PS3 over and lay it on its backside.
-
Carefully peel the warranty sticker up off the lower case to reveal a hidden screw cover.
-
-
-
Use the flat end of a metal spudger to pry up the seven screw covers around the edge of the lower case.
-
-
-
Remove the seven 37 mm Phillips screws securing the top cover to the lower case.
-
-
-
Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening. (Some models may only have three screws)
-
-
-
Lift the top cover from its rear edge and rotate it toward the front of the PS3.
-
Lift the top cover off the PS3.
-
-
-
Squeeze the AC inlet connector's locking mechanism and pull straight up to disconnect it from the power supply.
-
-
-
Pull the DC-Out cables straight up to lift their connector up and out of its socket on the power supply.
-
-
-
Remove the two 7.6 mm Phillips screws securing the power supply to the lower case.
-
-
-
Lift the power supply upward from its left edge as viewed from the front of the PS3.
-
-
-
Continue to lift the left edge of the power supply until it lifts off the two metal posts shown in the second picture.
-
Remove the power supply from the PS3, minding any cables that may get caught.
-
-
-
Use the flat end of a spudger or your fingernail to flip up the retaining flap on the Blu-ray ribbon cable socket.
-
-
-
-
Pull the Blu-ray power cable straight up to lift its connector out of the socket on the Blu-ray drive.
-
-
-
Remove the single 9.5 mm Phillips screw securing the Blu-ray drive to the lower case.
-
-
-
Lift the Blu-ray drive slightly by its right edge to dislodge the control board from its housing.
-
Remove the Blu-ray drive from the PS3.
-
-
-
Pull the AC-In cables upward to remove the AC inlet from the lower case.
-
-
-
Use the flat end of a spudger to pry both antenna connectors up from their sockets on the motherboard.
-
-
-
Pull the control board ribbon cable up and out of its socket on the motherboard.
-
Remove the control board.
-
-
-
Turn the PS3 over and lay it on its backside.
-
Use the flat edge of a metal spudger to pop up the small access door on the bottom cover near the front of the PS3.
-
Remove the blue Phillips screw hidden under the access door.
-
-
-
Slide the hard drive bay cover toward the right side of the lower case, then pull it away from the front edge to remove it from the PS3.
-
-
-
Remove the following five screws securing the motherboard assembly to the lower case:
-
Two silver 6 mm Phillips
-
Three black 8 mm Phillips
-
-
-
Lift the motherboard assembly from its front edge and remove it from the lower case, minding the antenna cable still attached to the lower case.
-
-
-
Disconnect the DC-In and Blu-ray power cables from the motherboard.
-
-
-
Pull the fan cables straight up to lift the fan connector up and out of its socket on the motherboard.
-
-
-
Remove the following nine screws holding the motherboard assembly together:
-
Four 14.8 mm shouldered Phillips
-
Five 9.5 mm Phillips
-
-
-
Gently press the board away from the top shield assembly near the fan connector and the corner of the board near the wireless sockets.
-
-
-
Remove the two 9.5 mm Phillips screws securing the fan to the heat sink.
-
-
-
Remove the fan from the heat sink, minding the cables that may get caught on the fan shroud.
-
-
-
Remove the four 9.5 mm Phillips screws securing the heat sink to the top shield.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
Отменить: Я не выполнил это руководство.
41 участников успешно повторили данное руководство.
7 Комментариев
Thanks for this guide
Hi, is the heatsink that makes contact with the cpu die aluminium? I think I might have repasted it with liquid metal… Thanks!