Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Remove the battery.
-
Turn the keyboard locking screw so that it is parallel to the space bar.
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
-
Этот шаг не переведен. Помогите перевести
-
Rest the keyboard face down on the trackpad area.
-
Disconnect the keyboard connector from the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to ÒpopÓ up.
-
Pull the RAM chip out.
-
Repeat this process if a second RAM chip is installed.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the G4 over.
-
Remove the eight T8 Torx screws from the lower case.
-
-
Этот шаг не переведен. Помогите перевести
-
Using your thumbs, slide the lower case away from you.
-
Lift the lower case off.
-
-
Этот шаг не переведен. Помогите перевести
-
Firmly grasp the plastic tab attached to the Airport card and pull up and to the left.
-
Disconnect the antenna cable from the left side of the Airport card.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger, removing tape as necessary.
-
-
Этот шаг не переведен. Помогите перевести
-
To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the hard drive by gently grasping the orange ribbon cable and lifting the left edge up and out of the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over, making sure the DVD drive doesn't fall out. Place the computer on the cloth.
-
-
Этот шаг не переведен. Помогите перевести
-
Bend the silver metal EMI clip so that it is vertical. This part may fall out after removing the DVD drive.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the G4 over.
-
Disconnect the orange DVD ribbon cable from the logic board using a spudger or the tip of your finger
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the DVD drive by lifting the right edge up and out of the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the G4 over.
-
Using a 5 mm nut driver or needle-nose pliers, remove the hex nut from the modem.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single T8 Torx screw located near the silver heat pipe.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the three indicated connectors from the logic board.
-
Disconnect the orange PC card cage connector from the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the G4 over.
-
Remove the three T8 Torx screws from the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the indicated connectors from the logic board, removing tape as necessary.
-
-
Этот шаг не переведен. Помогите перевести
-
Carefully lift the logic board up and pull it away from you.
-
Remove the logic board from the computer.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two T8 Torx screws that secure the PC Card cage.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the PC Card cage by pulling it to the right and twisting slightly toward you.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the four black T8 Torx screws from the plastic framework.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the five silver T8 Torx screws from the metal framework.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the G4 over.
-
Grasp the plastic framework and pull directly up.
-
-
Этот шаг не переведен. Помогите перевести
-
Position the display at a 45 degree angle and rest the computer on a soft cloth with the back panel ports facing up.
-
Remove the two T8 Torx screws from each clutch cover.
-
-
Этот шаг не переведен. Помогите перевести
-
Close the display and pull off both clutch covers. You can use a non-metal flathead screwdriver if the clutch covers do not come off easily.
-
-
Этот шаг не переведен. Помогите перевести
-
Open the back panel port cover and remove the four T6 Torx screws.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the audio cable at the right side of the computer, removing tape as necessary.
-
-
Этот шаг не переведен. Помогите перевести
-
Open the display to a 90 degree angle. Rest the trackpad face down on the work surface and allow the display to hang over the edge. If possible, adjust your chair or work surface height so the display will rest on your legs and the trackpad will lie flat on the work surface.
-
Remove the four T8 Torx screws that fasten the display to the trackpad. The screw closest to the display data cable has a tapered head.
-
-
Этот шаг не переведен. Помогите перевести
-
Grasp the metal heat exchanger and pull up and away from you. You may need to move the inverter cable on the right side of the computer in order to rotate the heat exchanger.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift up the metal brackets on either side of the upper case.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the inverter cable and carefully thread it through the slot in the upper case.
-
Carefully thread the display and backlight cables individually through the slot in the upper case. Be very careful with the display cable as it is easily damaged.
-
Remove the display assembly.
-
Отменить: Я не выполнил это руководство.
2 участников успешно повторили данное руководство.