Введение

How to remove and replace the hard drive.

Запчасти

Никакие детали не требуются.

Remove the 7 mm Philip screws.
  • Remove the 7 mm Philip screws.

  • Remove the 10 mm Philip screws.

  • Remove the 14 mm Philip screw.

Добавить комментарий

Open the flap on the left hand side. Open the flap on the left hand side.
  • Open the flap on the left hand side.

Добавить комментарий

Insert the iPod opening tools between the right and left sides of the latch. Pry the right side  of the latch, and then pry the left side to detach the laptop's cover.
  • Insert the iPod opening tools between the right and left sides of the latch.

  • Pry the right side of the latch, and then pry the left side to detach the laptop's cover.

Добавить комментарий

Open the flap on the right side. Open the flap on the right side.
  • Open the flap on the right side.

Добавить комментарий

Insert the iPod opening tools towards the right side of the latch.
  • Insert the iPod opening tools towards the right side of the latch.

  • Gently pry the right side out to release the top cover.

Добавить комментарий

Lift the keyboard slowly. A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.
  • Lift the keyboard slowly.

  • A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.

Добавить комментарий

Use your fingers or a spudger to detach the connector.
  • Use your fingers or a spudger to detach the connector.

Добавить комментарий

Carefully lift and remove the keyboard. Carefully lift and remove the keyboard.
  • Carefully lift and remove the keyboard.

Добавить комментарий

On the back of the computer, use a Flathead screwdriver to remove this lone screw.
  • On the back of the computer, use a Flathead screwdriver to remove this lone screw.

Добавить комментарий

After the screw is out, gently remove the cover. After the screw is out, gently remove the cover.
  • After the screw is out, gently remove the cover.

Добавить комментарий

Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.
  • Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.

Добавить комментарий

Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.
  • Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.

Добавить комментарий

Remove the final two screws (shown) and slide out the hard drive. Remove the final two screws (shown) and slide out the hard drive.
  • Remove the final two screws (shown) and slide out the hard drive.

Добавить комментарий

Заключение

To reassemble your device, follow these instructions in reverse order.

2 участников успешно повторили данное руководство.

Derek Driscoll

Member since: 15.04.2010

110 Репутация

Автор 16 руководств

Команда

Cal Poly, Team 26-27, Regan Spring 2010 Member of Cal Poly, Team 26-27, Regan Spring 2010

CPSU-REGAN-S10S26G27

3 членов

Автор 18 руководств

Один комментарий

You don't have to go to this length to remove the hard drive on a 560Z. Only do steps 0 (remove battery), 9 (remove screw) and 10 (remove cover). Then simply grab the blue tab of the hard drive caddy and pull the drive out of the bay. Complete directions on maintenance of the IBM Thinkpad 560Z can be found here:

http://www.thinkpads.com/support/hmm/hmm...

The Hardware Maintenance Manual has all of the information you need to take a 560Z apart and put it back together.

The procedure outlined here is similar to what the 560, 560E and 560X systems required; the 560Z is totally different when removing the hard drive.

Raymond - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 0

За 7 дней: 3

За 30 дней: 15

За всё время: 2,456