Перейти к основному содержанию

Отремонтируйте ваше устройство

Обучение ремонту

Запчасти и инструменты

Введение

If you don't have the heating pad available, either use a heat gun or a hair dryer with a high heat setting.

  1. Starting at any corner, insert the pry tool between the chrome screen frame and black phone housing. Slide the pry tool around the tablet while applying force to pry the screen away from the phone housing.
    • Starting at any corner, insert the pry tool between the chrome screen frame and black phone housing.

    • Slide the pry tool around the tablet while applying force to pry the screen away from the phone housing.

  2. Carefully separate the rear housing from the front panel assembly.
    • Carefully separate the rear housing from the front panel assembly.

  3. Using the bent tweezers, carefully pull the flat cables away from the connectors. Do not bend the flat cables at the tips as they may become permanently deformed. Do not bend the flat cables at the tips as they may become permanently deformed.
    • Using the bent tweezers, carefully pull the flat cables away from the connectors.

    • Do not bend the flat cables at the tips as they may become permanently deformed.

  4. Using the plastic opening tool, gently pry the chip connections away from the motherboard. Using the plastic opening tool, gently pry the chip connections away from the motherboard. Using the plastic opening tool, gently pry the chip connections away from the motherboard.
    • Using the plastic opening tool, gently pry the chip connections away from the motherboard.

  5. Essential Electronics Toolkit

    Small Toolkit. Big Possibilities.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits
  6. Use the Phillips 000 screwdriver to remove the remaining five 1.2 mm screws. Use the Phillips 000 screwdriver to remove the remaining five 1.2 mm screws.
    • Use the Phillips 000 screwdriver to remove the remaining five 1.2 mm screws.

  7. Use extreme care while removing the motherboard to avoid damaging the component. Remove the motherboard by rotating it away from the rest of the phone as shown in the first photo.
    • Use extreme care while removing the motherboard to avoid damaging the component.

    • Remove the motherboard by rotating it away from the rest of the phone as shown in the first photo.

  8. You do not need to remove the motherboard in order to remove the battery as the photos may indicate. Work the spudger underneath the battery as shown and pry the battery away from the phone case. The battery is attached to the case with adhesive, so a bit of force is required during removal.
    • You do not need to remove the motherboard in order to remove the battery as the photos may indicate.

    • Work the spudger underneath the battery as shown and pry the battery away from the phone case.

    • The battery is attached to the case with adhesive, so a bit of force is required during removal.

  9. Evenly heat the surface of the screen using your heating tool to loosen the adhesive that is holding the screen to the phone case. If using the heating pad, you may have to reheat it once or twice during this process.
    • Evenly heat the surface of the screen using your heating tool to loosen the adhesive that is holding the screen to the phone case.

    • If using the heating pad, you may have to reheat it once or twice during this process.

    • If you're using a heat gun, avoid heating one spot for more than a few seconds.

  10. Carefully insert the spudger between the glass and the chrome outer frame of the tablet. Now, slowly pry your way around the screen to loosen the glass from the frame. Now, slowly pry your way around the screen to loosen the glass from the frame.
    • Carefully insert the spudger between the glass and the chrome outer frame of the tablet.

    • Now, slowly pry your way around the screen to loosen the glass from the frame.

  11. After you’ve removed the glass from the screen, feed the chip connection through the phone casing. The screen may need a little more force to separate from the upper edge of the tablet. The screen may need a little more force to separate from the upper edge of the tablet.
    • After you’ve removed the glass from the screen, feed the chip connection through the phone casing.

    • The screen may need a little more force to separate from the upper edge of the tablet.

Заключение

To reassemble your device, follow these instructions in reverse order.

31 участников успешно повторили данное руководство.

Aubrey Goodwin

Участник с: 31.08.2015

2 494 Репутация

Автор 3 руководств

Команда

USF Tampa, Team 1-3, Remmell Fall 2015 Участник USF Tampa, Team 1-3, Remmell Fall 2015

USFT-REMMELL-F15S1G3

4 членов

Автор 12 руководств

Комментариев: 10

Where is the microfuse located?

bbruns - Ответить

Do you have to remove the battery to replace the screen?

Vic Rector - Ответить

This is digitizer replacement guide - not screen replacement !!

K P - Ответить

This worked perfectly for me. Thank you!

gjarmour - Ответить

This worked perfectly for me. I just bought the assembly instead of going through the full deal (which if I had it would have saved me about 30 bucks overall). But was easy enough to do anyway. I still intend to get the digitizer/glass and finish so I have a spare for future breaks. (I have kids and they are hard on these tablets)

gjarmour - Ответить

Добавить комментарий

Просмотр статистики:

За последние 24часов: 7

За последние 7 дней: 40

За последние 30 дней: 195

За всё время: 42,277