Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Switch off the phone.
-
If you can't switch it off, you can use the OFF button near to the SIM card Tray.
-
Warm the Back Cover. You can use a hairdryer.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a small suction cup and plastic tools for separating the Rear panel.
-
-
Этот шаг не переведен. Помогите перевести
-
Before installing the new cover, you must clean the phone from the old adhesive tape and install a new one (if your spare part has come without double sided adhesive tape).
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the Battery Flex Cable and remove the two Philips screws.
-
Li-Polymer Battery, 3.8V, 3200mAh
-
Part number: LIS1543ERPC
-
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two Phillips screws that hold Loudspeaker/Vibromotor module.
-
Disconnect the Coaxial Antenna cable.
-
-
Этот шаг не переведен. Помогите перевести
-
With the sharp end of the plastic tool carefully subtract the module from the phone housing.
-
The Loud Speaker has some adhesive holding it to the chassis so a little heat on the front will help.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the Touchscreen flex cables.
-
Disconnect the LCD Display flex cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a transparent packaging tape and stick it on top of the glass. This will help you remove the broken glass later.
-
Preheat the Display.
-
Use a cutter to make a room for a plastic tool.
-
-
Этот шаг не переведен. Помогите перевести
-
Continue separating the display from the frame by using plastic opening tools.
-
-
Этот шаг не переведен. Помогите перевести
-
Clean the frame from the remains of tape.
-
Now it's time to test the new spare part.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a high quality adhesive sticker for the model.
-
This will stick the display to the frame harder and it will save the waterproof ability of your phone.
-
-
Этот шаг не переведен. Помогите перевести
-
Use again adhesive sticker to atach the back / battery cover.
-
All's well that ends well.
-
Отменить: Я не выполнил это руководство.
61 участников успешно повторили данное руководство.
22 Комментариев
Worked! I very much recommend watching the video as well as read the manual to get a complete picture. My total time spent was multiple hours, but largely because it's the first time I'm doing a repair that involves so much glue. Gained a few gray hairs there.
Two stumbles:
I missed the line "The load Speaker has some adhesive holding it to the chassis so a little heat on the front will help.", which cost me a lot of time and worry as I was trying to force the speaker assembly out. Eventually got it out, and it's fine. Ribbon cables will be the death of me some day.
I did not keep the little bit of tape on the display ribbon safe and clean and ended up not using it at all. The written manual doesn't show its reuse, the video does.
Also: getting (almost) all of the glue goop off the back was a tragedy.
so cool, is simple.
My Xperia Z2 touch screen is fixed at a phone repaircenter. I dont know what they do but since that day it looks like my touchscreen living his own life. Especially if i type some text with the stock keyboard. Its very frustrating and my question is.....can i do something about it myself?
Sorry for my bad English btw
Before gluing the screen to work well sensors and all that, you need to put some black tape on the camera or sensors?
Is it and seen online tutorials or is not necessary