Введение

This guide give instructions on how to locate the speaker for removal and/or repair.

Запчасти

Никакие детали не требуются.

Flip over the phone and then slide down the back cover with your thumb.
  • Flip over the phone and then slide down the back cover with your thumb.

Добавить комментарий

Lever out the battery from the phone using your thumb.
  • Lever out the battery from the phone using your thumb.

Добавить комментарий

With the phone closed, run a plastic opening tool along the seam of the top half of the phone Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top) Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)
  • With the phone closed, run a plastic opening tool along the seam of the top half of the phone

  • Make sure to disconnect each of the five clips before proceeding (2 on each side, 1 on top)

Добавить комментарий

Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel Note that the fourth screw is under a fold in the ribbon cable
  • Using T6 Torx Screwdriver, remove the four 3.16mm screws from the front panel

  • Note that the fourth screw is under a fold in the ribbon cable

Добавить комментарий

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down Be careful around the two ribbon cables that are attached to the tape, they are fragile Lift the tape from the board
  • Starting in the lower right corner, slowly start to lift the tape that is holding the front LCD and cables down

  • Be careful around the two ribbon cables that are attached to the tape, they are fragile

  • Lift the tape from the board

Добавить комментарий

Using a plastic opening tool, lift the ribbon cable connection below the front LCD
  • Using a plastic opening tool, lift the ribbon cable connection below the front LCD

Добавить комментарий

Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board
  • Using a plastic opening tool, slowly pry up the LCD display from the bottom, releasing it from the glue holding it to the board

Добавить комментарий

Locate the ribbon cable connection in the upper right hand corner of the board
  • Locate the ribbon cable connection in the upper right hand corner of the board

  • Using a plastic opening tool, lift off the cable from the board

  • Be gentle and make sure not to rip the ribbon cable

Добавить комментарий

Using a plastic opening tool, slowly work the board off the mounts holding it to the frame Flip the board over to reveal the main display
  • Using a plastic opening tool, slowly work the board off the mounts holding it to the frame

  • Flip the board over to reveal the main display

Добавить комментарий

Locate the ribbon cable for the main display on the bottom of the board
  • Locate the ribbon cable for the main display on the bottom of the board

  • Slowly lift off the ribbon connector from its housing using a plastic opening tool

Добавить комментарий

Slowly wedge the plastic opening tool under the bottom of the main display Separate the display from the glue lifting it off the board
  • Slowly wedge the plastic opening tool under the bottom of the main display

  • Separate the display from the glue lifting it off the board

Добавить комментарий

Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.
  • Using a case opening tool, gently pry the speaker in the bottom corner from the glue from right to left until it pops out.

Добавить комментарий

Заключение

To reassemble your device, follow these instructions in reverse order.

Andrew

Member since: 04.10.2010

358 Репутация

Автор 8 руководств

Команда

Cal Poly, Team 4-46, Amido Fall 2010 Member of Cal Poly, Team 4-46, Amido Fall 2010

CPSU-AMIDO-F10S4G46

4 членов

Автор 14 руководств

Комментариев: 0

Добавить комментарий

Просмотр статистики:

За 24 часа: 0

За 7 дней: 0

За 30 дней: 1

За всё время: 411