Skip to main content

Changes to Samsung Galaxy S Phone Custom-cut Adhesive Replacement Introduction

Edit by Arthur Shi

Правка одобрена by Arthur Shi

Deleted
Added
Unchanged
Introduction
right place![br] [br] This place! This guide shows how to use the back cover adhesive kit for the Galaxy S series with glass backs (S7 and newer). It also includes instructions on how to transfer and install various back cover components, such as the camera rear bezel and fingerprint sensor. [ … ] You''You may not need to use all the adhesive strips included in the kit. kit.'' If you are transferring the fingerprint sensor, you will may need some double-sided tape such as Tesa tape. [ … ] For a list of adhesive strips for the Galaxy S phone, [https://www.ifixit.com/Store/Parts/Samsung-Galaxy-S-Series/Adhesive_Strips|follow this link]. [ … ] When applying adhesive strips like these, here are some general tips: [ … ] * '''The adhesive exposed when peeling the clear liner determines which surface the strip should be applied to first.''' This layer usually peels easily. Locate the surface that aligns with the exposed adhesive. * To make adhesive application easier, you can align an unexposed strip to its intended position on the phone, then [https://d3nevzfk7ii3be.cloudfront.net/igi/a6EfdSi3YTRDsMVw.large|tape one edge down to hold the strip in place]. This will allow you to peel away the plastic liners and expose the adhesive without losing alignment. * When you are ready to apply the adhesive, '''peel away the clear plastic liner first'''. This layer usually peels easily. If there are multiple clear plastic layers, remove the clear layer that exposes adhesive. * '''The adhesive exposed after peeling the clear liner determines which surface the strip should be applied to first.''' Locate the surface that aligns with the exposed adhesive.
right place![br] [br] This place! This guide shows how to use the back cover adhesive kit for the Galaxy S series with glass backs (S7 and newer). It also includes instructions on how to transfer and install various back cover components, such as the camera rear bezel and fingerprint sensor. [ … ] You''You may not need to use all the adhesive strips included in the kit. kit.'' If you are transferring the fingerprint sensor, you will may need some double-sided tape such as Tesa tape. [ … ] For a list of adhesive strips for the Galaxy S phone, [https://www.ifixit.com/Store/Parts/Samsung-Galaxy-S-Series/Adhesive_Strips|follow this link]. [ … ] When applying adhesive strips like these, here are some general tips: [ … ] * '''The adhesive exposed when peeling the clear liner determines which surface the strip should be applied to first.''' This layer usually peels easily. Locate the surface that aligns with the exposed adhesive. * To make adhesive application easier, you can align an unexposed strip to its intended position on the phone, then [https://d3nevzfk7ii3be.cloudfront.net/igi/a6EfdSi3YTRDsMVw.large|tape one edge down to hold the strip in place]. This will allow you to peel away the plastic liners and expose the adhesive without losing alignment. * When you are ready to apply the adhesive, '''peel away the clear plastic liner first'''. This layer usually peels easily. If there are multiple clear plastic layers, remove the clear layer that exposes adhesive. * '''The adhesive exposed after peeling the clear liner determines which surface the strip should be applied to first.''' Locate the surface that aligns with the exposed adhesive.
Imageid
Before
After

Запчасти

  • Precut Adhesive Card x1 added.
  • Tesa 61395 Tape x1 removed.

Steps

Step #: 1
Before
After
Step #: 2
Before
After
Step #: 3
Before
After
Step #: 4
Before
After
Step #: 5
Before
After
Step #: 6
Before
After
Step #: 7
Before
After
Step #: 8
Before
After
Step #: 9
Before
After
Step #: 10
Before
After
Step #: 11
Before
After
Step #: 12
Before
After
Step #: 13
Before
After
Step #: 14
Before
After
Step #: 15
Before
After