Перейти к основному содержанию

iMac LCD Cleanup

Выберете то, что вам нужно

  1. iMac LCD Cleanup, LCD Dust removal: шаг 1, изображение 1 из 1
  2. iMac LCD Cleanup: шаг 2, изображение 1 из 1
    • Face the LCD down (be sure to have nothing between the screen and the table) ;

    • Remove 4 screws from the left bracket then 4 screws from the right bracket as displayed (the smallest is at the bottom) ;

  3. iMac LCD Cleanup: шаг 3, изображение 1 из 3 iMac LCD Cleanup: шаг 3, изображение 2 из 3 iMac LCD Cleanup: шаг 3, изображение 3 из 3
    • Use a "Putty Knife" to separate brackets from the LCD panel frame as shown ;

    • Use a "Post-It" to keep the adhesive from the frame ;

    • Continue gently between the bracket and the frame ;

  4. iMac LCD Cleanup: шаг 4, изображение 1 из 2 iMac LCD Cleanup: шаг 4, изображение 2 из 2
    • Using the "Putty Knife" make a groove in the shield around the whole frame ;

    • Once done from the bottom center to the edges of the LCD panel unclip the frame (don't touch the top). Clips are located at :

    • Bottom left, center, right ;

    • Left bottom, top ;

    • Right bottom, top ;

    • Lift the frame 90° maximum ;

  5. iMac LCD Cleanup: шаг 5, изображение 1 из 3 iMac LCD Cleanup: шаг 5, изображение 2 из 3 iMac LCD Cleanup: шаг 5, изображение 3 из 3
    • Using gloves and a suction cup gently lift the LCD sheet (no more than 90° failing to do so may bend the LCD and cause image displaying issues);

    • Meticulously clean the inside. Do not use any detergent at most a very lightly humidified microfiber / lint-free cloth ;

    • Do not use an air spray as those might leave marks. Best to get rid of dust is a simple hair dryer going from the top center to the edges ;

    • Reassembly is going back those steps making sure to get rid of your finger-prints ;


To reassemble your device, follow these instructions in reverse order.

20 участников успешно повторили данное руководство.


Участник с: 11/25/13

981 Репутация

1 руководство автора

24 Комментариев

Thank you for this guide! Helped me very much. And now my iMac is clean again :)

Robert - Ответить

I got the screen cleaned and all was well but when I returned everything back to the iMac the lower part of my screen didn't work...

Chris Malka - Ответить

If the backligt is ok but no image check connections :

— To the logic board ;

— Then underneath the protective cover on the top of step 2 image…

If the backlight is not ok check the connector and the cable at the lower right corner of step 2 image.

Beware that if you have bended the LCD you might have damaged it.

LLange -

It sounds like the LCD got bent then because the connections are fine so I just ordered a new LCD. But the guide was definitely helpful, I got the dust out!

Chris Malka -

Sorry about this I'm adding a warning on Step 5 to lift gently and no more than 90° hoping this might prevent others to have the same issue.

P.S. the LCD has an electronic board some times people have flickering issues after the display warmed-up. Thus changing that "inner-board" might solve their issue ⇒ after you receive your new LCD, try to sell the old display "inner-board" as well as the connectors…

LLange -

Добавить комментарий

Просмотр статистики:

За последние 24часов: 3

За последние 7 дней: 26

За последние 30 дней: 132

За всё время: 39,462