Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Heat the iOpener for thirty seconds.
-
Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.
-
-
Этот шаг не переведен. Помогите перевести
-
Fill a pot or pan with enough water to fully submerge an iOpener.
-
Heat the water to a boil. Turn off the heat.
-
Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.
-
Use tongs to extract the heated iOpener from the hot water.
-
Thoroughly dry the iOpener with a towel.
-
Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.
-
-
Этот шаг не переведен. Помогите перевести
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Safety Glasses$3.19-
Lay the iOpener flat on the right edge of the iPad, smoothing it out so that there is good contact between the surface of the iPad and the iOpener.
-
Let the bag sit on the iPad for approximately 90 seconds before attempting to open the front panel.
-
-
Этот шаг не переведен. Помогите перевести
-
There is a small gap in the iPad's adhesive ring in the upper right corner of the iPad, approximately 2.0 inches (~5 cm) from the top of the iPad. You are going to exploit this weakness.
-
Align the tool with the mute button. Insert the tip of a plastic opening tool into the gap between the front glass and the plastic bezel. Just insert the very tip of the opening tool, just enough to widen the crack.
-
-
Этот шаг не переведен. Помогите перевести
-
Make sure you place the tool in the proper spot—between the plastic display bezel and the front panel glass.
-
-
Этот шаг не переведен. Помогите перевести
-
Keeping the tip of the plastic opening tool wedged between the front glass and plastic bezel, slide a plastic opening pick in the gap, right next to the plastic opening tool.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the plastic opening tool from the iPad, and push the opening pick further underneath the front glass to a depth of ~0.5 inches.
-
-
Этот шаг не переведен. Помогите перевести
-
While you work on releasing the adhesive on the right side of the iPad, reheat the iOpener, and replace it on the bottom edge of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
While the bottom edge is being heated by the iOpener, begin releasing the adhesive from the right edge of the iPad.
-
Slide the opening pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
Этот шаг не переведен. Помогите перевести
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
Этот шаг не переведен. Помогите перевести
-
Before removing the first opening pick from the bottom corner of the iPad, insert a second pick under the right edge of the front glass to keep the adhesive from re-adhering.
-
Re-heat the iOpener, and move it to the top edge of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
You will have to release the adhesive securing the antenna to the front panel without damaging the delicate parts attaching the antenna to the bottom of the iPad. Follow the next steps carefully.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the opening pick around the bottom right corner of the iPad, releasing the adhesive there.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the tip of the opening pick along the bottom edge of the iPad, releasing the adhesive over the Wi-Fi antenna.
-
-
Этот шаг не переведен. Помогите перевести
-
Once you have moved past the Wi-FI antenna (approximately 3" (75 mm) from the right edge, or right next to the home button) re-insert the opening pick to its full depth.
-
Slide the pick to the right, releasing the adhesive securing the Wi-Fi antenna to the front glass.
-
The antenna is attached to the bottom of the iPad via screws and a cable. This step detaches the antenna from the front panel, ensuring that when you remove the panel, the antenna will not be damaged.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Continue releasing the adhesive along the bottom of the iPad, pulling the opening pick out far enough to go around the home button, and re-inserting it to a depth of 1/2 inch (10 mm) once the pick is past the home button.
-
-
Этот шаг не переведен. Помогите перевести
-
Continue releasing the adhesive all the way along the bottom edge of the iPad.
-
Leave the opening pick wedged underneath the front glass near the home button.
-
-
Этот шаг не переведен. Помогите перевести
-
Reheat the iOpener in the microwave and set it on the left edge of the iPad to start warming the adhesive in that section.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the opening pick along the top edge of the iPad, pulling it out slightly to go around the front-facing camera bracket.
-
The adhesive along this section is very thick, and a fair amount of force may be required. Work carefully and slowly, making sure to not slip and damage yourself or your iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Continue releasing the adhesive along the top edge of the iPad, and slide the opening pick around the top left corner.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the opening pick along the left edge of the iPad, releasing the adhesive as you go. The adhesive is thin here due to the digitizer along the whole left side. Make sure the pick is not too deep (max 1/2 inch) 10 mm to prevent damaging the digitizer.
-
-
Этот шаг не переведен. Помогите перевести
-
Using the opening pick that is still underneath the bottom edge of the iPad, release the adhesive along the bottom left corner.
-
-
Этот шаг не переведен. Помогите перевести
-
Using one of the opening picks, pry up the bottom right corner of the iPad and grab it with your fingers.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Microfiber Cleaning Cloths$3.99-
Holding the iPad by the top and bottom right corners, rotate the front glass away from the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the four 2.0 mm Phillips screws securing the LCD to the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the LCD from its long edge closest to the volume buttons and gently flip it out of the rear case—like turning the page in a book.
-
Set the LCD face down on the front panel.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Tweezers$4.99-
If present, remove the piece of tape covering the end of the front facing camera cable with a pair of tweezers.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to carefully pry the connector up from its socket on the control board.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to separate the adhesive securing the front facing camera cable to the control board.
-
-
Этот шаг не переведен. Помогите перевести
-
Pry the front-facing camera up off the foam adhesive securing it to the rear case.
-
Remove the front-facing camera.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Tweezers$4.99-
Use a pair of tweezers to remove the rubber cover up off the rear-facing camera housing.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single 3.3 mm Phillips screw from the rear-facing camera metal retainer clip.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the rear-facing camera metal retainer clip straight up from its recess in the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
Use a plastic opening tool to pry the rear-facing camera connector up from its socket on the control board.
-
Remove the rear-facing camera.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single 2.1 mm Phillips screw from the rear-facing camera housing.
-
Remove the camera housing from the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to flip up the retaining flap on the button assembly ribbon cable ZIF socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Run the tip of a spudger underneath the button assembly cable to free it from the socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to flip up the retaining flap on the microphone ribbon cable ZIF socket.
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Tweezers$4.99-
Pull the microphone ribbon cable straight out with a pair of tweezers.
-
Gently bend the cable to keep it out of the way.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two 2.9 mm Phillips screws securing the headphone jack to the rear case.
-
Pull the headphone jack from its port in the rear case and fold out of the way.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the two 2.1 mm Phillips screws securing the metal bracket to the rear case.
-
Remove the metal bracket from the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
If present, use tweezers to remove the piece of tape covering the end of the headphone jack/control board cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to flip up the retaining flap on the headphone jack/control board cable ZIF socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the tip of a spudger underneath the ribbon cable to disconnect it.
-
-
Этот шаг не переведен. Помогите перевести
-
Gently peel the headphone jack/control board ribbon cable away from the rear case to free it from the adhesive.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to loosen the adhesive under the narrower part of the ribbon cable near the headphone jack.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the flat end of a spudger under the middle portion of the ribbon cable to separate the adhesive holding it to the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the flat end of a spudger under the widest part of the cable to free it from the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
To begin freeing it from adhesive, pry gently under the control board near the front-facing camera socket.
-
-
Этот шаг не переведен. Помогите перевести
-
Pry gently under the control board near the rear-facing camera.
-
Carefully pry under the widest part of the board to free the assembly from the last of the adhesive.
-
Отменить: Я не выполнил это руководство.
15 участников успешно повторили данное руководство.