Эта версия возможно содержит некорректные исправления. Переключить на последнюю проверенную версию.
Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
Heat the iOpener for thirty seconds.
-
Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.
-
-
Этот шаг не переведен. Помогите перевести
-
Fill a pot or pan with enough water to fully submerge an iOpener.
-
Heat the water to a boil. Turn off the heat.
-
Place an iOpener into the hot water for 2-3 minutes. Make sure the iOpener is fully submerged in the water.
-
Use tongs to extract the heated iOpener from the hot water.
-
Thoroughly dry the iOpener with a towel.
-
Your iOpener is ready for use! If you need to reheat the iOpener, heat the water to a boil, turn off the heat, and place the iOpener in the water for 2-3 minutes.
-
-
Этот шаг не переведен. Помогите перевести
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Этот шаг не переведен. Помогите перевести
-
Handling it by the tabs on either end, place a heated iOpener over the top edge of the iPad.
-
Let the iOpener sit on the iPad for two minutes to soften the adhesive securing the front panel to the rest of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
As you follow the directions, take special care to avoid prying in the following areas:
-
Home Button
-
Front Facing Camera
-
Main Camera
-
-
Этот шаг не переведен. Помогите перевести
Инструмент, используемый на этом этапе:Anti-Clamp$24.95-
Elevate the iPad enough for the Anti-Clamp's arms to rest above and below the screen.
-
Pull the blue handle towards the hinge to disengage opening mode.
-
Position the suction cups near the top edge of the iPad—one on the front, and one on the back.
-
Push down on the cups to apply suction to the desired area.
-
-
Этот шаг не переведен. Помогите перевести
-
Push the blue handle away from the hinge to engage opening mode.
-
Turn the handle clockwise until you see the cups start to stretch.
-
Wait one minute to give the adhesive a chance to release and present an opening gap.
-
Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next two steps.
-
-
Этот шаг не переведен. Помогите перевести
-
Place a suction cup over the iPad's front-facing camera and press down to create a seal.
-
-
Этот шаг не переведен. Помогите перевести
-
Firmly pull up on the suction cup to create a small gap between the front panel and the rear case.
-
Once you've opened a sufficient gap, insert an opening pick into the gap to prevent the adhesive from resealing.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the pick along the edge of the display, towards the headphone jack.
-
If there is still a considerable amount of resistance when sliding the opening pick, repeat the iOpener heating procedure and apply additional heat.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the second pick along the top edge of the iPad, towards the Sleep/Wake Button.
-
-
Этот шаг не переведен. Помогите перевести
-
Bring the right opening pick down and around the top right corner of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Bring the left opening pick around the top left corner of the tablet.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Reheat the iOpener and lay it over the right edge of the display to loosen the adhesive underneath.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the right opening pick roughly halfway down the display.
-
-
Этот шаг не переведен. Помогите перевести
-
Reheat the iOpener and apply heat to the left side of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the left-hand opening pick about halfway down the edge of the display.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the opposite opening pick down to the bottom right corner of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the left-hand opening pick down the edge of the display until you reach the corner.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the iOpener to apply heat to the bottom edge of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Bring the right-hand opening pick around the bottom corner of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the right-hand opening pick at the bottom of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide the left-hand opening pick along the bottom edge of the display, then remove it from the bottom right corner of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Twist the remaining pick by the front-facing camera to separate the top edge of the display assembly from the rear case.
-
-
Этот шаг не переведен. Помогите перевести
-
Continue lifting the display assembly from the front-facing camera side.
-
Pull the display slightly away from the bottom edge to completely separate it from the rear case.
-
Keep lifting until the display assembly is roughly perpendicular to the body of the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the single 1.8 mm Phillips screw securing the battery terminals to their contacts on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Slide a battery isolation pick underneath the battery connector area of the logic board, and leave it in place while you work.
-
Alternatively, make a battery blocker using a playing card and slide it underneath the logic board connector to disconnect the battery.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the three 1.3mm Phillips screws from the display cable bracket.
-
Remove the bracket.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the display data connector from its socket on the logic board.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the two remaining digitizer cables underneath the display data cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following four Phillips screws securing the upper component cable bracket to the tablet.
-
Two 1.6 mm
-
Two 1.3 mm
-
Slide the upper component cable bracket out from under the protective flaps and remove it from the iPad.
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the antenna cables by gently prying them straight up from their sockets.
-
-
Этот шаг не переведен. Помогите перевести
-
Firmly grasp the antenna cable and peel up the grounding tape attaching it to the motherboard.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following four Phillips screws from the right antenna bracket:
-
Three 1.4 mm screws
-
One 1.5 mm screws
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the right Wi-Fi antenna out of its housing and remove it.
-
-
Этот шаг не переведен. Помогите перевести
-
Grasp the antenna cable with tweezers and gently peel up the grounding tape.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to pry up the FaceTime camera cable socket from its socket.
-
Pry the cable up to free it from the adhesive securing it to the rear case.
-
Fold the FaceTime camera cable up and out of the way.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the flat end of a spudger to pry up the audio jack cable connector from its socket.
-
Pry the cable up to free it from the adhesive securing it to the rear case.
-
Fold the ribbon cable to the left, out of the way of the antenna cable.
-
-
Этот шаг не переведен. Помогите перевести
-
Peel up the two remaining pieces of grounding tape attaching the left antenna to the rear case, as done in the previous steps.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the following four Phillips screws securing the left Wi-Fi antenna:
-
Three 1.4 mm screws
-
One 1.5 mm screw
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the left Wi-Fi antenna out of its housing and remove it.
-
Отменить: Я не выполнил это руководство.
8 участников успешно повторили данное руководство.
2 Комментариев
I installed as directed. Thanks for that. Easy to follow. But still no wifi?
chuck it out the window then
Diogo F -