Перейти к основному содержанию
  1. Этот шаг не переведен. Помогите перевести

    Completely power down your iPad before you begin. If your screen glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass. Lay overlapping strips of clear packing tape over the iPad's screen until the whole face is covered.
    • Completely power down your iPad before you begin.

    • If your screen glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.

    • Lay overlapping strips of clear packing tape over the iPad's screen until the whole face is covered.

    • This will keep glass shards contained and provide structural integrity when prying and lifting the screen.

    • Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.

    • Wear safety glasses to protect your eyes, and be careful not to damage the LCD screen.

  2. Этот шаг не переведен. Помогите перевести

    Removing the screen involves using an opening pick or halberd spudger to separate the adhesive securing the screen to the frame. As you slice through the adhesive, note the following:
    • Removing the screen involves using an opening pick or halberd spudger to separate the adhesive securing the screen to the frame.

    • As you slice through the adhesive, note the following:

    • The top has a large patch of thick adhesive. You'll need to slice 1/2" deep in order to cut the adhesive.

    • Don't slice deeper than 2 mm along the long edges of the iPad, or you risk damaging the display panel.

    • The lower edge also has thick patches of adhesive, but there are delicate flex cables in each corner. Don't slice deeper than 1/4" around the lower corners.

  3. Этот шаг не переведен. Помогите перевести

    Heat an iOpener and lay it over the left edge of the iPad to soften the adhesive holding the screen in place. Alternatively, you can use a heat gun, hair dryer, or heat pad.
    • Heat an iOpener and lay it over the left edge of the iPad to soften the adhesive holding the screen in place.

    • Alternatively, you can use a heat gun, hair dryer, or heat pad.

    • Be careful not to overheat the iPad—the display and internal battery are both susceptible to heat damage.

    • Wait about two minutes for the adhesive to soften before proceeding to the next step. The edge should be slightly too hot to the touch.

  4. Этот шаг не переведен. Помогите перевести

    Attach a suction cup to the left edge of the iPad's screen, above the Smart Connector port.
    • Attach a suction cup to the left edge of the iPad's screen, above the Smart Connector port.

  5. Этот шаг не переведен. Помогите перевести

    While holding down the corners of the iPad, repeatedly pull up on the screen, then ease it back down to weaken the adhesive. This will eventually create a small gap in the seam. If the edge cools down during the pulling process, reheat the edge with an iOpener before proceeding. Once you've created a small gap, insert the tip of an opening pick into the gap.
    • While holding down the corners of the iPad, repeatedly pull up on the screen, then ease it back down to weaken the adhesive. This will eventually create a small gap in the seam.

    • If the edge cools down during the pulling process, reheat the edge with an iOpener before proceeding.

    • Once you've created a small gap, insert the tip of an opening pick into the gap.

    • Don't insert the pick more than 2 mm, or you risk permanently damaging the display panel.

  6. Этот шаг не переведен. Помогите перевести

    Lay a hot iOpener along the bottom left corner of the iPad, spanning from the opening pick to the home button. After letting the adhesive soften, insert an opening pick or halberd spudger into the gap next to the Smart Connector. Be careful not to insert the opening pick more than 2 mm.
    • Lay a hot iOpener along the bottom left corner of the iPad, spanning from the opening pick to the home button.

    • After letting the adhesive soften, insert an opening pick or halberd spudger into the gap next to the Smart Connector.

    • Be careful not to insert the opening pick more than 2 mm.

    • Use an opening pick or halberd spudger to slice the adhesive along the bottom left side of the iPad. If the slicing becomes difficult, reheat the edge and try again.

  7. Этот шаг не переведен. Помогите перевести

    Insert a pick in the bottom left corner of the iPad to prevent the adhesive from resealing.
    • Insert a pick in the bottom left corner of the iPad to prevent the adhesive from resealing.

  8. Этот шаг не переведен. Помогите перевести

    Lay a hot iOpener along the upper left corner of the iPad, spanning from the opening pick to the front-facing camera. Wait a minute to let the adhesive soften. Use an opening pick to slice the adhesive along the upper left side of the iPad. If the slicing becomes difficult, reheat the edge and try again. Be careful not to insert the opening pick more than 2 mm as you slice along the left edge.
    • Lay a hot iOpener along the upper left corner of the iPad, spanning from the opening pick to the front-facing camera. Wait a minute to let the adhesive soften.

    • Use an opening pick to slice the adhesive along the upper left side of the iPad. If the slicing becomes difficult, reheat the edge and try again.

    • Be careful not to insert the opening pick more than 2 mm as you slice along the left edge.

  9. Этот шаг не переведен. Помогите перевести

    Insert a pick in the upper left corner of the iPad to prevent the adhesive from resealing.
    • Insert a pick in the upper left corner of the iPad to prevent the adhesive from resealing.

  10. Этот шаг не переведен. Помогите перевести

    Reheat your iOpener and lay it over the top edge of the device. Wait a couple minutes for the adhesive to soften. Use an opening pick to slice through the top edge of the iPad, stopping before you reach the front-facing camera. The adhesive is thicker along the top. You'll need to slice 1/2" deep—about the thickness of the top bezel.
    • Reheat your iOpener and lay it over the top edge of the device. Wait a couple minutes for the adhesive to soften.

    • Use an opening pick to slice through the top edge of the iPad, stopping before you reach the front-facing camera.

    • The adhesive is thicker along the top. You'll need to slice 1/2" deep—about the thickness of the top bezel.

    • If the slicing becomes hard, reheat the edge and try again.

  11. Этот шаг не переведен. Помогите перевести

    Insert an opening pick just before the front-facing camera to keep the adhesive from resealing. Insert an opening pick just before the front-facing camera to keep the adhesive from resealing.
    • Insert an opening pick just before the front-facing camera to keep the adhesive from resealing.

  12. Этот шаг не переведен. Помогите перевести

    Reheat your iOpener and lay it over the top edge of the device. Wait a couple minutes for the adhesive to soften. Insert an opening pick or a halberd spudger blade just past the front-facing camera. Use the opening pick to slice through the adhesive in the upper right corner.
    • Reheat your iOpener and lay it over the top edge of the device. Wait a couple minutes for the adhesive to soften.

    • Insert an opening pick or a halberd spudger blade just past the front-facing camera.

    • Use the opening pick to slice through the adhesive in the upper right corner.

    • You'll need to slice 1/2" deep—about the thickness of the top bezel.

    • If the slicing becomes hard, reheat the edge and try again.

  13. Этот шаг не переведен. Помогите перевести

    Insert an opening pick in the upper right corner to prevent the adhesive from resealing. Insert an opening pick in the upper right corner to prevent the adhesive from resealing.
    • Insert an opening pick in the upper right corner to prevent the adhesive from resealing.

  14. Этот шаг не переведен. Помогите перевести

    Soften the adhesive by heating the right edge of the iPad using an iOpener. Use an opening pick or halberd spudger to slice along the right edge of the iPad, till you reach the lower right corner. Don't insert the pick more than 2 mm along the right edge.
    • Soften the adhesive by heating the right edge of the iPad using an iOpener.

    • Use an opening pick or halberd spudger to slice along the right edge of the iPad, till you reach the lower right corner.

    • Don't insert the pick more than 2 mm along the right edge.

    • Leave an opening pick in the middle of the right edge to prevent the adhesive from resealing.

  15. Этот шаг не переведен. Помогите перевести

    Leave an opening pick in the lower right corner of the iPad to prevent the adhesive from resealing. Leave an opening pick in the lower right corner of the iPad to prevent the adhesive from resealing.
    • Leave an opening pick in the lower right corner of the iPad to prevent the adhesive from resealing.

  16. Этот шаг не переведен. Помогите перевести

    Use an iOpener to heat the lower edge of the iPad. Insert an opening pick or a halberd spudger blade 1/4" into the lower right corner of the iPad. Slide the opening pick along the lower edge of the iPad, stopping  short about 1/2" before reaching the home button.
    • Use an iOpener to heat the lower edge of the iPad.

    • Insert an opening pick or a halberd spudger blade 1/4" into the lower right corner of the iPad.

    • Slide the opening pick along the lower edge of the iPad, stopping short about 1/2" before reaching the home button.

    • Each lower corner has a thick patch of adhesive, but there is also a delicate flex cable. Don't slice deeper than 1/4" around the corner to prevent damaging the flex cable.

  17. Этот шаг не переведен. Помогите перевести

    Slide the tip of an opening pick or a halberd spudger to cut the adhesive below the home button. Slide the tip of an opening pick or a halberd spudger to cut the adhesive below the home button.
    • Slide the tip of an opening pick or a halberd spudger to cut the adhesive below the home button.

  18. Этот шаг не переведен. Помогите перевести

    After you slice below the home button, reinsert the tip of an opening pick or a halberd spudger blade 1/4" into the lower edge. Slice along the lower edge until you reach the opening pick.
    • After you slice below the home button, reinsert the tip of an opening pick or a halberd spudger blade 1/4" into the lower edge.

    • Slice along the lower edge until you reach the opening pick.

  19. Этот шаг не переведен. Помогите перевести

    At this point, you've sliced through most of the screen adhesive. Use an opening pick to carefully slice any remaining adhesive along the edges until the screen is freed. If some parts are stubborn, heat the area with an iOpener to loosen the adhesive.
    • At this point, you've sliced through most of the screen adhesive. Use an opening pick to carefully slice any remaining adhesive along the edges until the screen is freed. If some parts are stubborn, heat the area with an iOpener to loosen the adhesive.

  20. Этот шаг не переведен. Помогите перевести

    The display cables in this iPad are very short. Read the next two steps before you proceed. Do not pivot the screen about the lower edge. The display cables don't have enough slack to allow for this and will tear if you do not slide the screen towards the front-facing camera as you lift. The display cables will tear if you raise the screen more than 80º.
    • The display cables in this iPad are very short. Read the next two steps before you proceed.

    • Do not pivot the screen about the lower edge. The display cables don't have enough slack to allow for this and will tear if you do not slide the screen towards the front-facing camera as you lift.

    • The display cables will tear if you raise the screen more than 80º.

    • Lift up the upper edge of the screen and slide the entire screen towards the front-facing camera to access the iPad's internal components.

    • Use masking tape to tape the lower edge of the screen to the frame to prevent the screen from slipping.

  21. Этот шаг не переведен. Помогите перевести

    This step shows one way to support the screen using masking tape. You can also turn the iPad sideways. Make sure not to strain the display cables with whatever method you choose. Attach a long strip of masking tape to the top edge of the screen. Fold the tape over the edge and make sure that the tape is attached securely. Attach the other end of the strip to the bottom edge of the iPad frame to hold the screen at an angle. Make sure the tape attaches securely to the frame.
    • This step shows one way to support the screen using masking tape. You can also turn the iPad sideways. Make sure not to strain the display cables with whatever method you choose.

    • Attach a long strip of masking tape to the top edge of the screen. Fold the tape over the edge and make sure that the tape is attached securely.

    • Attach the other end of the strip to the bottom edge of the iPad frame to hold the screen at an angle. Make sure the tape attaches securely to the frame.

  22. Этот шаг не переведен. Помогите перевести

    It's important to disconnect the battery before you proceed further. Detaching or connecting the display cables with the battery plugged in can cause a short that will destroy touchscreen functionality.
    • It's important to disconnect the battery before you proceed further. Detaching or connecting the display cables with the battery plugged in can cause a short that will destroy touchscreen functionality.

    • Use a Phillips screwdriver to remove the nine screws securing the logic board EMI shield:

    • Eight 1.2 mm screws

    • One 2.4 mm screw

  23. Этот шаг не переведен. Помогите перевести

    Lift the logic board EMI shield from the edge nearest the top of the iPad. Peel up and remove the EMI shield from the logic board. This takes a bit of force due to the many tiny clips securing the shield, and the shield may deform slightly. That's okay—try to keep the deformation to a minimum, and it will lay flat when you reinstall it and screw it down.
    • Lift the logic board EMI shield from the edge nearest the top of the iPad.

    • Peel up and remove the EMI shield from the logic board.

    • This takes a bit of force due to the many tiny clips securing the shield, and the shield may deform slightly. That's okay—try to keep the deformation to a minimum, and it will lay flat when you reinstall it and screw it down.

    • Remove the logic board EMI shield.

  24. Этот шаг не переведен. Помогите перевести

    Use a Phillips screwdriver to remove the 1.8 mm screw securing the battery connector.
    • Use a Phillips screwdriver to remove the 1.8 mm screw securing the battery connector.

  25. Этот шаг не переведен. Помогите перевести

    These photos show what the battery connector looks like underneath the logic board. Use these photos as a reference while you safely disconnect the battery. Notice that the battery connector has springs on the logic board that press down against the battery contact pads. You'll need to slide something thin and flexible between the contact points to disconnect the battery. Notice that the battery connector has springs on the logic board that press down against the battery contact pads. You'll need to slide something thin and flexible between the contact points to disconnect the battery.
    • These photos show what the battery connector looks like underneath the logic board. Use these photos as a reference while you safely disconnect the battery.

    • Notice that the battery connector has springs on the logic board that press down against the battery contact pads. You'll need to slide something thin and flexible between the contact points to disconnect the battery.

  26. Этот шаг не переведен. Помогите перевести

    Make a battery blocker using a playing card and slide it underneath the logic board connector to disconnect the battery. You can also use an iFixit battery blocker. Be very careful and don't push the battery blocker underneath the connector with excessive force.
    • Make a battery blocker using a playing card and slide it underneath the logic board connector to disconnect the battery.

    • You can also use an iFixit battery blocker. Be very careful and don't push the battery blocker underneath the connector with excessive force.

    • Leave the blocker there to prevent the battery connector leads from making contact until you have completed your repairs.

  27. Этот шаг не переведен. Помогите перевести

    Use a Phillips screwdriver to remove the three screws securing the display cable bracket: Two 2.4 mm screws
    • Use a Phillips screwdriver to remove the three screws securing the display cable bracket:

    • Two 2.4 mm screws

    • One 1.2 mm screw

    • Remove the display cable bracket.

  28. Этот шаг не переведен. Помогите перевести

    Use the flat end of a spudger to pry up and disconnect the display and digitizer cables from their logic board sockets. To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage. To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.
    • Use the flat end of a spudger to pry up and disconnect the display and digitizer cables from their logic board sockets.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

  29. Этот шаг не переведен. Помогите перевести

    Remove the screen. Be sure to remove all remaining adhesive from the iPad's enclosure.
  30. Этот шаг не переведен. Помогите перевести

    Use tweezers to remove the tape covering the ZIF connector above the home button. Use tweezers to remove the tape covering the ZIF connector above the home button.
    • Use tweezers to remove the tape covering the ZIF connector above the home button.

  31. Этот шаг не переведен. Помогите перевести

    Use the point of a spudger to lift the flap on the ZIF connector that secures the cable. Use the point of a spudger to lift the flap on the ZIF connector that secures the cable.
    • Use the point of a spudger to lift the flap on the ZIF connector that secures the cable.

  32. Этот шаг не переведен. Помогите перевести

    Use tweezers to slide the cable out of the ZIF connector. Use tweezers to slide the cable out of the ZIF connector.
    • Use tweezers to slide the cable out of the ZIF connector.

  33. Этот шаг не переведен. Помогите перевести

    The home button's ribbon cable is very fragile. If it gets damaged, Touch ID will no longer function. Use an iOpener, heat gun, or hair dryer to soften the adhesive under the cable before you pry it up.
    • The home button's ribbon cable is very fragile. If it gets damaged, Touch ID will no longer function.

    • Use an iOpener, heat gun, or hair dryer to soften the adhesive under the cable before you pry it up.

    • Alternatively, apply a few drops of isopropyl alcohol to the cable and wait for a minute to let the adhesive soften.

  34. Этот шаг не переведен. Помогите перевести

    Starting from the ZIF connector, use an opening pick to separate the home button cable from the adhesive holding it in place. Stop when you reach the home button. Starting from the ZIF connector, use an opening pick to separate the home button cable from the adhesive holding it in place. Stop when you reach the home button. Starting from the ZIF connector, use an opening pick to separate the home button cable from the adhesive holding it in place. Stop when you reach the home button.
    • Starting from the ZIF connector, use an opening pick to separate the home button cable from the adhesive holding it in place. Stop when you reach the home button.

  35. Этот шаг не переведен. Помогите перевести

    The home button bracket is held in place with strong adhesive. Apply a few drops of isopropyl alcohol to the base of the home button bracket. Alternatively, you can use a heated iOpener to loosen the adhesive.
    • The home button bracket is held in place with strong adhesive.

    • Apply a few drops of isopropyl alcohol to the base of the home button bracket.

    • Alternatively, you can use a heated iOpener to loosen the adhesive.

  36. Этот шаг не переведен. Помогите перевести

    Insert the edge of an opening tool under the home button bracket lip. Pry up with steady force to loosen the bracket.
    • Insert the edge of an opening tool under the home button bracket lip.

    • Pry up with steady force to loosen the bracket.

    • The adhesive holding this bracket can be stubborn. Apply more isopropyl alcohol or heat if it doesn't budge.

  37. Этот шаг не переведен. Помогите перевести

    • Remove the home button bracket.

    • During reassembly, after installing the home button, you'll need to glue this bracket into place to secure it.

    • Scrape off as much of the old adhesive residue as you can, then clean it with acetone or high concentration (>90%) isopropyl alcohol.

    • Secure the bracket with hot-melt glue, superglue, or high-strength double-sided tape. Make sure the bracket is aligned correctly before allowing your adhesive to cure, or the home button will not click when pressed.

  38. Этот шаг не переведен. Помогите перевести

    Gently push the home button from the front of the display inward using the tip of a finger. Gently push the home button from the front of the display inward using the tip of a finger.
    • Gently push the home button from the front of the display inward using the tip of a finger.

  39. Этот шаг не переведен. Помогите перевести

    Remove the home button.
    • Remove the home button.

    • The home button attaches to the screen with an adhesive gasket. When you transfer the home button to a new display, use some liquid adhesive to glue the button perimeter to the screen.

  40. Этот шаг не переведен. Помогите перевести

    Only the screen remains.
    • Only the screen remains.

  41. Этот шаг не переведен. Помогите перевести

    When you install a replacement screen: Remove all packing tape.
    • When you install a replacement screen:

    • Remove all packing tape.

    • Peel any adhesive liners from the flex cables and press the cables in place onto the display panel.

    • Fold and connect the flex cable in the bottom left corner of the screen.

    • Don't peel and expose the perimeter adhesive until you've tested your repair and are ready to seal up the iPad.

Финишная черта

77 участников успешно повторили данное руководство.

Evan Noronha

Участник с: 05.02.2015

210 582 Репутация

Автор 178 руководств

Команда

iFixit Участник iFixit

Community

138 членов

Автор 15 583 руководств

Комментариев: 16

Hello there OK so I have 2 screens with 2 different connectors one L shaped (which is on the new screen) and the old cracked screen has a rectangular type? I’m not sure rather it’s a 1gen/2nd gen type of problem? I’m about to grab my hot air gun to completely disassemble the cracked screen, as maybe I’m missing something? Any assistance is welcome… well actually please help me with this before I get a headache since this has totally frustrated me and i’ve had this sitting for nearly 2 1/2 months now but it’s about that time that I readdress this in attempt to fix it.

Matthew Newton - Ответить

Hi, does your replacement screen have the home button assembly included? Otherwise there's need of soldering the assembly to it before it can be installed.

Dreetn -

hi

does anyone knows why there is a foam adhesive in thr back of the screen ? do i need to put back when i replaxe screen ?

thanks

screensguy - Ответить

I suppose the foam adhesive is similar to the one on the back of the 6s screens. I guess it has more of a heat dissipation function or is meant to absorb any pointy pressure points from inside that may develop (loose screw, sand, dirt...)

Dreetn -

hi

hope someone can help . i tested couple of screens before fitting them in they were working but once tech close it there no touch or black lcd (backlight on but no image )

NB : they disconnect battery before connecting Screen

screensguy - Ответить

If you don't have this problem while the assembly is still loose, my best guess is that you have an unwanted contact somewhere, causing a short circuit or malfunction. Perhaps in the bending of the flex?

Dreetn -

Removing the screen takes a great degree of patience. You apply heat, and pull on the suction cup, and for a long time nothing seems to happen. Do not try to replace time with force at this point keep heating and pulling on various areas, you will get separation. It took 5 or 6 heating/pulling cycles to start to see results. Then you can work your way around.

oclark - Ответить

MAKE SURE YOU DO NOT INSERT ANY CARDS/PICKS/SPUDGERS MORE THAN 1/4 inch tops!! YOU WILL DAMAGE THE SCREEN. Just replaced the battery in my iPad Pro 12.9 (A1652). Unfortunately I did not read this until completed. I now have several areas on my $1000 iPad where the white screen has orange burn looking marks around the edges. Looks like it was a $200 oops. Live and Learn. I’m now a member and will utilize this website for future endeavors…

Dave Ryberg - Ответить

You know any workshop who does a repair for my three iPad Pro 12.9 front glasses with the digitizer,

Sometimes the process is called OCA refurbishment oder LCD refurbishment.

NOT the display-unit as a whole. I have two models from 2015 and one from 2017. The model numbers are a 1584 and  a 1670.

 In Germany there are a few companies who are able to do it, but not affordable. The prices are nearly as high as a complete swap of the display unit.

giuseppe naniscola - Ответить

Just wondering, I work in a repair shop, and am replacing the front panel entirely but unfortunately screwed up soldering the daughterboard. Is this a part they MUST be transferred or am I safe to just replace it?

Zane Clark - Ответить

Hello.

Is it possible to change only the “Glas” and not the Display? My display works fine but the Protecting Glas is broken.

sim sem - Ответить

Hi, that’s possible for very, very experienced technicians. Not only do you need to heat up the screen quite a lot to soften up the LOCA glue, but furthermore you need to cut it with a cutting wire while making sure not to damage the LCD underneath. I also fear the iPad pro will probably require some micro-soldering to be able to (dis)connect the glass from all the rest (but perhaps I’m confusing things with the first screen modules in mind that came out but still needed some micro-soldering to finish them of at that time). In short, if you haven’t separated touchscreens/glass plates several times before … don’t even think about it. The above is only half the trouble to go through as the new touchscreen/glass needs to be attached to the LCD again with new LOCA glue afterwards. Again a job which requires a lot of expertise.

Dreetn -

I used this guide to replace a screen for my iPad Pro. The device powers on but now gets stuck in a boot loop. I took it to a local phone repair shop and they said they don’t do repairs on iPad Pros because they always get stuck in boot loops. I wish there was a warning on this guide telling people this so they don’t go to all the effort and spend money on a new screen just to get their iPad stuck in a boot loop.

Brandon der Blatter - Ответить

Brandon, I don’t know of any specific ‘sensitivity’ that iPad Pro’s have towards repairing that would result in bootloops.

I think it is more likely that either

- The repair shop isn’t keen on repairing your device because parts are expensive and/or difficult to find (for instance motherboard parts). They just tell you a believable story to avoid having to say ‘Too risky’ or ‘Not worth our effort/time’.

- Something got damaged during the repair.

Another possibility, which you can easily put aside yourself, is software damage. Try a full restore (without data retention) with tools such as 3uTools. It’s free software. I advise using the iTunes restore method. You can first try a restore with ‘retain user’s data’ but success ratio is minimal there. Best is to go for a clean flash/restore.

Good luck!

Dreetn -

No matter how many times I have tried to apply the iOpener, or to use a dryer for 10 mins (iPad was super hot), I’m simply unable to lift the screen with the suction cup, even for a micron. Anything I could have missed ?

Laurent Crivello - Ответить

Hi Laurent, it sounds like you’re on the right track—continue gradually applying more heat until the adhesive softens a little. Unfortunately these screens are super hard to remove. Just be careful about applying too much heat at once in a small area as that could damage the screen.

Adam O'Camb -

Добавить комментарий

Просмотр статистики:

За последние 24часов: 72

За последние 7 дней: 382

За последние 30 дней: 1,952

За всё время: 99,800