Почините Свои Вещи Сообщество Магазин

iPhone 14 Plus 屏幕替换

Требования для руководства

Все предварительные руководства должны быть переведены до того, как этот перевод будет считаться завершённым.

iPhone 14 Pro Max 五角螺丝更换

三角撬片深度标记

iPhone 14 Plus 屏幕替换前提指南

Информационный справочник

= Готово = Не завершен
Английский
Китайский
    If your iPhone 14 Plus screen is cracked, not responding to touch, or not showing a picture when your phone is powered on, use this guide to restore your iPhone to working order with a new screen, a.k.a. display assembly.
    This guide was created using the ***A2886*** (international) model. If you're fixing a different iPhone 14 Plus model, there may be some visual discrepancies, but the procedure should be the same.
    ***Note:***: On iOS 17.6 and earlier, True Tone and auto brightness functionality areis disabled after a screen replacement, even when using an original Apple screen. Face ID is also disabled, unless the iPhone runsis running iOS 15.2 or newer. On iOS 18 and newer, you can calibrate your new screen using Apple's [link|https://support.apple.com/en-us/120579|Repair Assistant|new_window=true] to restore True Tone functionality on genuine screens purchased from Apple.
    You’ll need replacement adhesive to reattach the screen when reassembling the device. Your device will function normally, but will most likely lose its IP (Ingress Protection) rating.
      If possible, turn on your device and test your repair before installing new adhesive and resealing.
      ***To reassemble your device, follow these instructions in reverse order.***
      After your repair, depending on the replacement part, you may be able to [link|https://support.apple.com/en-us/120579|calibrate it using Apple's Repair Assistant|new_window=true], available as of iOS 18. Update your device, navigate to Settings ***→*** General ***→***About ***→*** Parts & Service History, tap Restart & Finish Repair, and follow the onscreen prompts.
      The best way to secure the new screen is to apply a sheet of custom-cut double-sided tape to the frame and place the screen back in its original position.
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers/Ask/iPhone+14+Plus|Answers community] for help.

      Шаги руководства

      Шаг 1 — 松开前传感器盖

      其余步骤演示如何将 前传感器组件 转移到新屏幕。 如果更换屏幕已预装组件，请跳过这些步骤。

      Шаг 2 — 拆下前传感器盖

      使用镊子或手指卸下前传感器组件盖。

      Шаг 3 — 加热前传感器组件

      将加热过的iOpener 放在在屏幕顶部上至少两分钟，以软化胶水。

      Шаг 4 — 断开环境光传感器

      在环境光传感器和它在屏幕上的凹槽之间插入撬片。

      Шаг 5 — 断开接近传感器

      在接近传感器和屏幕上的凹槽之间插入三角撬片。

      Шаг 6 — 移开接近传感器

      使用镊子或手指将接近传感器排线从屏幕上移开。

      Шаг 7 — 断开麦克风

      在麦克风电缆下方插入三角撬片，靠近麦克风（金属矩形）。

      Шаг 8 — 拆下前传感器组件

      此时，粘合剂可能已经冷却下来。 如果是这样，在继续之前将加热的 iOpener 应用到组件上一分钟。

      Шаг 9

      拆下前传感器组件。

      Ваш вклад лицензируется под свободной лицензией Creative Commons .