Почините Свои Вещи Сообщество Магазин

Nintendo 3DS - Wie man den Kartenleser austauscht

Назад к руководству
Английский
Немецкий
Следующий шаг

Перевод шага 1

Шаг 1
Nintendo 3DS Cartridge Reader Replacement, Opening the Cover: шаг 0, изображение 1 из 1
Opening the Cover

  • Use a JIS #00 screwdriver to loosen the four screws along the top of the back cover. These screws stay in the cover after loosing them.

  • JIS (Japanese Industrial Standards) screws are not the same as Phillips. To avoid stripping these screws, make sure you are using a JIS #00 screwdriver and not a PHILLIPS #00 screwdriver. You can use a PHILLIPS #00 with a lot of downwards force but be warned this will deform the screw head and you risk stripping it.

  • iFixit's Phillips head screwdriver is designed to reduce damage on JIS head screws so it should be fine to use, still apply more force. Make sure it's iFixit's official Phillips screwdriver as we are unaware of any other manufacturer who does this.

Öffnen der Abdeckung des Batteriefaches:

Benutze einen JIS #00 Schraubendreher, um die vier Schrauben der Abdeckung der Unterseite zu lösen. Diese Schrauben sind an der Abdeckung befestigt, du musst dir also keine Sorgen machen sie zu verlieren.

JIS (Japanischer IndustrieStandard) Schrauben haben NICHT das selbe Profil wie Phillips (PH) #00 Schrauben! Um zu vermeiden, die Schraubenköpfe auszufransen, verwende einen JIS anstelle eines PH Schraubendrehers.

Du kannst einen PH00 Schraubendreher verwenden, wenn du genug Druck auf die Schraube anwendest. Dies wird jedoch deinen Schraubenkopf mindestens verformen, sei daher vorsichtig.

Der Phillips Schraubendreher von iFixit ist dafür ausgelegt, einigermaßen sicher an JIS Schrauben zu arbeiten. Stelle also wenn du es nicht vermeiden kannst sicher, einen iFixit Schraubendreher zu verwenden, da wir nicht wissen ob andere Hersteller auch für Kompatibilität sorgen.

Wenn du die Abdeckung gelöst hast, nimm zuallererst die Batterie heraus.

[title] Opening the Cover
-[* red] Use a JIS #00 screwdriver to loosen the four screws along the top of the back cover. This screws stay in the cover after loosing them.
+[* red] Use a JIS #00 screwdriver to loosen the four screws along the top of the back cover. These screws stay in the cover after loosing them.
[* icon_caution] JIS (Japanese Industrial Standards) screws are ***not*** the same as Phillips. To avoid stripping these screws, make sure you are using a JIS #00 screwdriver and not a PHILLIPS #00 screwdriver. You ''can'' use a PHILLIPS #00 with a lot of downwards force but be warned this ***will*** deform the screw head and you risk stripping it.
-[* icon_note] IFixIt's Phillips head screwdriver is designed to reduce damage on JIS head screws so it should be fine to use, still apply more force. Make sure it's IFixIt's official Phillips screwdriver as we are unaware of any other manufacturer who does this.
+[* icon_note] iFixit's Phillips head screwdriver is designed to reduce damage on JIS head screws so it should be fine to use, still apply more force. Make sure it's iFixit's official Phillips screwdriver as we are unaware of any other manufacturer who does this.

Ваш вклад лицензируется под свободной лицензией Creative Commons .