Отремонтируйте ваше устройство

Обучение ремонту

Магазин

Примечание: Вы редактируете необходимое руководство. Любые внесённые вами изменения влияют на все 18 руководства, которые включают этот шаг.

Назад к руководству
Английский
Японский
Предыдущий шаг

Перевод шага 3

Шаг 3
Use the clear plastic pull tab to gently lift the battery out of the iPhone. If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive. Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • Use the clear plastic pull tab to gently lift the battery out of the iPhone.

  • If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.

  • Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

  • If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

  • If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.

  • Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.

  • Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.

  • Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

透明のプラスチック製プルタブを使って丁寧にiPhoneからバッテリーを引っ張ります。

バッテリーを取り出す前にプルタブが裂けてしまった場合は、丁寧にスパッジャーをバッテリータブの下に差し込んで接着剤を剥がしてください。他の場所から差し込むとダメージを与えてしまいます。

交換するバッテリーがプラスチック製スリーブに入っている場合、取り付ける前にリボンケーブルから引き抜いて外します。

バッテリーコネクターを再接続する前に、コンタクトクリップ（赤でマークされています）がバッテリーコネクターの隣の正しい位置に装着されているか確認してください。

再組み立ての前に、メタル接合ポイントをwindex（窓拭き用クリーナー）などで綺麗に拭き取ってください。油脂がワイヤレス通信の妨害となることがあります。

再組み立ての後はハードリセットを行ってください。これはトラブルシューティングを簡単にして、幾つかの問題を防いでくれます。

[* black] Use the clear plastic pull tab to gently lift the battery out of the iPhone.
[* icon_cautionicon_note] If the tab breaks before the battery is freed, carefullyapply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.
[* icon_caution] Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
[* black] If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
[* icon_cautionicon_note] If the tab breaks before the battery is freed, carefullyapply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.
[* icon_caution] Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
[* black] If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
[* icon_note] If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.
[* red] Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.
[* icon_reminder] Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.
[* icon_reminder] Perform a [guide|44489|hard reset] after reassembly. This can prevent several issues and simplify troubleshooting.

Ваш вклад лицензируется под свободной лицензией Creative Commons.