Перейти к основному содержанию

Эта разборка продолжается – Периодически обновляйте, чтобы увидеть последние изменения!

Выберете то, что вам нужно

  1. (TC) PlayStation Teardown, (TC) PlayStation Teardown: шаг 1, изображение 1 из 1
    • Flip the unit upside down to access the six screws on the bottom.

    • Remove the six screws indicated with a Phillips-head screwdriver. All the screws are of the same length.

  2. (TC) PlayStation Teardown: шаг 2, изображение 1 из 1
    • Turn the unit back over, and pull the top half up and away from the device.

  3. (TC) PlayStation Teardown: шаг 3, изображение 1 из 1
    • Unplug the laser assembly's power cable and ribbon cable from the main board.

    • Remove the two screws on the memory card/controller port, disconnect the ribbon cable, and lift it out of the case.

  4. (TC) PlayStation Teardown: шаг 4, изображение 1 из 2 (TC) PlayStation Teardown: шаг 4, изображение 2 из 2
    • To remove the power supply, disconnect the cable and remove the two screws, then lift it out of the case.

  5. (TC) PlayStation Teardown: шаг 5, изображение 1 из 2 (TC) PlayStation Teardown: шаг 5, изображение 2 из 2
    • Remove the 3 screws from the shield.

  6. (TC) PlayStation Teardown: шаг 6, изображение 1 из 2 (TC) PlayStation Teardown: шаг 6, изображение 2 из 2
    • Remove the 5 Phillips screws.

    • You can now lift the main board out of the case.

  7. (TC) PlayStation Teardown: шаг 7, изображение 1 из 2 (TC) PlayStation Teardown: шаг 7, изображение 2 из 2
    • Lift the RF shield out of the case.

  8. (TC) PlayStation Teardown: шаг 8, изображение 1 из 2 (TC) PlayStation Teardown: шаг 8, изображение 2 из 2
    • Reinstall the RF shield by dropping it in and lining up the slots and tabs.

  9. (TC) PlayStation Teardown: шаг 9, изображение 1 из 2 (TC) PlayStation Teardown: шаг 9, изображение 2 из 2
    • Replace the main board. Only install the screws indicated in red.

  10. (TC) PlayStation Teardown: шаг 10, изображение 1 из 1
    • Replace the top shield, and secure with the 3 screws indicated.

    • Reinstall the memory card / controller module. Connect the ribbon cable and replace the 2 screws.

  11. (TC) PlayStation Teardown: шаг 11, изображение 1 из 1
    • Align the optical drive assembly with the three pegs.

    • Reconnect the power and data cables for the optical drive.

  12. (TC) PlayStation Teardown: шаг 12, изображение 1 из 1
    • Slide the cover on the system in the same way you took it off and replace the black screws indicated.

  13. (TC) PlayStation Teardown: шаг 13, изображение 1 из 1
    • Plug in the console and turn it on.

    • Thanks for looking at my teardown!

Nick

Участник с: 11/10/09

88 298 Репутация

Автор 49 руководств

Команда

Master Techs Участник Master Techs

Community

322 членов

Автор 2 495 руководств

0 Комментариев

Добавить комментарий

Просмотр статистики:

За последние 24часов: 0

За последние 7 дней: 4

За последние 30 дней: 29

За всё время: 43,001