Перейти к основному содержанию

This teardown is in progress – Reload periodically to see the latest changes!

Инструменты для этого Разбора

  1. Front and back of the Flip Ultra HD Front and back of the Flip Ultra HD
    • Front and back of the Flip Ultra HD

  2. Locate the lock/unlock latch at the bottom of The Flip Ultra HD 2nd Generation and slide it into the unlock position. Locate the lock/unlock latch at the bottom of The Flip Ultra HD 2nd Generation and slide it into the unlock position.
    • Locate the lock/unlock latch at the bottom of The Flip Ultra HD 2nd Generation and slide it into the unlock position.

  3. Pull down on the large front cover to to expose the battery slots.
    • Pull down on the large front cover to to expose the battery slots.

  4. Pry off the top of the camcorder with a flat head screwdriver. The cover is glued on with adhesive so it will take some force to dislodge it from the device. Pry off the top of the camcorder with a flat head screwdriver. The cover is glued on with adhesive so it will take some force to dislodge it from the device. Pry off the top of the camcorder with a flat head screwdriver. The cover is glued on with adhesive so it will take some force to dislodge it from the device.
    • Pry off the top of the camcorder with a flat head screwdriver. The cover is glued on with adhesive so it will take some force to dislodge it from the device.

  5. Комплект инструментов для замены батареи Macbook

    Доступно с $69.99

    Buy Now

    Комплект инструментов для замены батареи Macbook

    Доступно с $69.99

    Buy Now
  6. Use a small Phillips head screwdriver to remove the two screws at the bottom of the battery slot and the two screws above the camera lens. Use a small Phillips head screwdriver to remove the two screws at the bottom of the battery slot and the two screws above the camera lens. Use a small Phillips head screwdriver to remove the two screws at the bottom of the battery slot and the two screws above the camera lens.
    • Use a small Phillips head screwdriver to remove the two screws at the bottom of the battery slot and the two screws above the camera lens.

  7. Gently pull off back cover of the camcorder.  Once again, it is glued with adhesive Gently pull off back cover of the camcorder.  Once again, it is glued with adhesive
    • Gently pull off back cover of the camcorder. Once again, it is glued with adhesive

  8. Remove the ribbon cable gently and pull the back cover off Remove the ribbon cable gently and pull the back cover off
    • Remove the ribbon cable gently and pull the back cover off

  9. Remove all of the screws on the circuit board Make sure to remove the screw behind the display Make sure to remove the screw behind the display
    • Remove all of the screws on the circuit board

    • Make sure to remove the screw behind the display

  10. There are two wires with white heads connecting the circuit board to the front of the device. Gently pull them from their slots to detach the front casing from the circuit board. There are two wires with white heads connecting the circuit board to the front of the device. Gently pull them from their slots to detach the front casing from the circuit board.
    • There are two wires with white heads connecting the circuit board to the front of the device. Gently pull them from their slots to detach the front casing from the circuit board.

  11. The disassembled Flip Ultra HD
    • The disassembled Flip Ultra HD

Charlie Tran

Участник с: 29.10.2011

150 Репутация

1 Guide authored

Один комментарий

Where can I buy the usb cable that goes to the flip board?

I botched mine in an attempt to resolder the usb connector back.

mein kampf - Ответить

Добавить комментарий

Просмотр статистики:

За 24 часа: 2

За 7 дней: 2

За 30 дней: 4

За всё время: 4,441