Выберете то, что вам нужно
-
Этот шаг не переведен. Помогите перевести
-
There she is, one of the two original PS3 models available at launch (60GB).
-
It's got PS2/PS1 backwards compatibility and a multi-card reader. The current PS3 Slim doesn't have the card reader. The other launch model lacked the card reader and WiFi (20GB).
-
-
Этот шаг не переведен. Помогите перевести
-
Let's get started!
-
Remove the hard drive access cover from the bottom of the PS3.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift up the metal lever.
-
Slide the hard drive towards the front of the case.
-
Pull it straight up and out of the unit.
-
This is all you need to do to access the PS3's hard drive.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the warranty sticker.
-
Use your fingers and pry up and remove the foot underneath the sticker.
-
-
Этот шаг не переведен. Помогите перевести
-
Use the Torx Screwdriver (T8 or T10) to remove the torx screw from the space behind the rubber foot.
-
-
Этот шаг не переведен. Помогите перевести
-
Place PlayStation face up such that "PlayStation 3" is oriented so you can read it.
-
Place your palm on the PlayStation 3 logo and slide the plastic front cover towards you and off of the outer plastic shell. Set it aside.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the metal receiver that held the torx screw you just removed.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 9 screws from the outer plastic shell using a #2 Philips driver.
-
6 large screws
-
1 medium screw
-
2 small screws
-
-
Этот шаг не переведен. Помогите перевести
-
Disconnect the ribbon cable and set the shell aside.
-
If you want to remove the plastic card reader, locate its two locking plastic tabs that hold the card reader to the shell, spread them, and lift the card reader off of the shell.
-
-
Этот шаг не переведен. Помогите перевести
-
To remove the plastic card reader, locate its two locking plastic tabs that hold the card reader to the shell, spread them, and lift the card reader off of the shell.
-
-
Этот шаг не переведен. Помогите перевести
-
Working on the main unit, lift up on and disconnect the black RF wire from the wireless assembly using a spudger.
-
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the four Philips #2 screws from the top of the wireless assembly.
-
-
Этот шаг не переведен. Помогите перевести
-
Lift the wireless assembly off the main board and set it aside.
-
Disconnect the ribbon cable from the main board and place it with the wireless assembly.
-
-
Этот шаг не переведен. Помогите перевести
-
Locate the other wireless assembly which the black RF wire is connected to.
-
Remove the one Philips #2 screw retaining it to the main board and lift off the assembly and set it aside.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the cables that attach the power supply to the main board.
-
Remove the AC connector from the power supply.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 5 screws using a Philips #2 from the power supply, and lift the power supply straight up and off of the main body. Set it aside.
-
-
Этот шаг не переведен. Помогите перевести
-
Unplug the power connector (gray) on the side of the player.
-
-
Этот шаг не переведен. Помогите перевести
-
READ THIS ENTIRE STEP BEFORE PROCEEDING. Lift the player up slowly to expose the folded ribbon cable beneath it.
-
Remove that ribbon cable from the main board and set the drive/cable aside.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the ribbon cable attaching the on/off and eject switch circuit board to the main board.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 4 Philips #2 screws retaining the circuit board to the case.
-
Remove the circuit board from the case.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 9 screws from the main body.
-
5 Medium Philips #2 Screws
-
2 Small Philips #1 Screws
-
1 Ground Philips Screw with Washer
-
1 Bolt Philips Screw (under AC cord)
-
-
Этот шаг не переведен. Помогите перевести
-
Grab the main board at the locations shown in the picture and lift the main board off of the back casing.
-
Set aside the black shell.
-
-
Этот шаг не переведен. Помогите перевести
-
On the main body, locate the 5 plastic locking tabs holding the rear plastic I/O shield to the main body.
-
Pry the tabs away from the body and lift the rear shield away.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 3 Philips #2 screws holding the fan to the main body.
-
These are extra small screws
-
Lift the fan straight up and out of the body.
-
Check out the size of this thing.
-
-
Этот шаг не переведен. Помогите перевести
-
On the top of the mainboard, EVENLY remove the four large Philips #2 screws holding the heat sink.
-
Remove the plates and the screws from the main board.
-
-
Этот шаг не переведен. Помогите перевести
-
Flip the main board over.
-
Lift (or pry with fingers) the heat sink straight off of the mainboard and processors.
-
-
Этот шаг не переведен. Помогите перевести
-
Remove the 2 Phillips #0 screws from the hard drive enclosure.
-
-
Этот шаг не переведен. Помогите перевести
-
To expose the mainboard, remove the watch battery from the mainboard.
-
-
Этот шаг не переведен. Помогите перевести
-
Using spudger, carefully pry the metal shielding away from and off of the top of motherboard.
-
-
Этот шаг не переведен. Помогите перевести
-
Turn the motherboard over and remove the metal shielding on the opposite side. Pry with a spudger or with your fingers.
-
-
Этот шаг не переведен. Помогите перевести
-
Check out all the chips with heatspreaders on this thing.
-
There's the Emotion Engine chip and Graphics Synthesis chip that allows the sweet backwards compatibility.
-
IBM Cell processor... This CPU has 9 cores, 10 threads and it runs @ 3.2GHz .
-
16 Комментариев
ii got a broken ps3 from my step dad, it turns on but theres no picture. I've taken it apart 3 times now and couldnt figure out how to get it fully apart. I've put everything back together and it does the same thing. So i didnt mess it up and more than it was. lol. From what i was told it was on top of a tv and a dog caught the cord and pulled it down. It slammed down on the back of the system and hasnt been able to show video and sound. Like i've said, i've tryed to mess with it but i know nothing about this stuff. Any ideas as to what could be broken? The port itself is cracked, but i've tryed HDMI and that doesnt work either. Any advice is helpful. Thank you.
lol couple years later, no all u have to do is switch out the fan inside your ps3 :) it happen to mine or buy a new ps3 and switch hard drives :)
It's the GPU
I love the way you post a warning as to how fragile the ribbon cable is and then say, "remove ribbon cable" without any detail as to how to release it. Thanks. Now my PS3 is trash.
Instructions not clear enough. Stuck my finger in a light socket.
10/10, would electrocute self again.