Введение

This is a teardown of the RIM Blackberry.

This teardown is not a repair guide. To repair your BlackBerry 7290, use our service manual.

  1. Apply pressure to the lock button on the back of the device.
    • Apply pressure to the lock button on the back of the device.

    • Slide the battery cover down towards the bottom of the device, revealing the battery compartment.

    Добавить комментарий

  2. Locate groove along the right side of the battery compartment.
    • Locate groove along the right side of the battery compartment.

    • Remove battery by prying between the battery and the groove.

    Добавить комментарий

    • Slide the SIM card holder to the left to unlock the SIM card.

    Добавить комментарий

    • Lift the SIM card holder up.

    • Gently remove the SIM card from the SIM card holder by sliding the card along the railing.

    Добавить комментарий

    • Locate the four screws along the perimeter of the back casing.

    • Remove the four top screws using a T-6 torx screwdriver.

    • The top four screws are .413 inches.

    Добавить комментарий

    • Locate two screws within the lower edge of the inner compartment.

    • Remove the two bottom screws using a T-6 torx screwdriver.

    • The bottom two screws are .2 inches in length.

    • The second picture displays the device after the six screws have been removed.

    Добавить комментарий

  3. Spread Fixmas Cheer
    Получите $12 за покупку от $50 и выше с промокодом FIXMAS12
    Spread Fixmas Cheer
    Получите $12 за покупку от $50 и выше с промокодом FIXMAS12
    • Use the plastic opening tool to apply pressure on the two clips that are located at the bottom of the phone.

    Добавить комментарий

    • Remove the back casing from the phone by lifting the unhooked portion, then slide the casing towards the top of the device.

    • Make sure all clips holding the case together are unhooked, so no damage is caused to the case.

    Добавить комментарий

    • Locate on the backside of the phone, a screw towards the top of the device.

    • Using a T-6 screwdriver, remove the screw.

    • After the screw has been removed, carefully lift the side button brace to reveal the side button.

    Добавить комментарий

    • To remove the phone's internals, start by loosening one side by pulling gently.

    Добавить комментарий

    • With one side loosened, simply lift the phone internals to separate from the front casing.

    Добавить комментарий

    • Turn the internals over to reveal the LCD display.

    Добавить комментарий

    • Peel off the rubber keypad buttons from the face plate.

    Добавить комментарий

    • Locate a hook on the right side of the internals below the volume wheel.

    • Use a plastic opening tool to gently pry the hook, separating the LCD display from the logic board mounting plate.

    Добавить комментарий

    • With the clip unhooked, gently separate the display from the phone internals by pulling.

    Добавить комментарий

    • On the front side of the internals, locate the the three screws that are highlighted in red.

    • Carefully remove screws from the internals, using a T6 torx screwdriver

    • The screw is .2 inches in length.

    Добавить комментарий

    • Separate the logic board mounting plate from the logic board by lifting with minimal force.

    Добавить комментарий

    • These are all the components of the phone.

    Добавить комментарий

kenny34

Участник с: 28.10.2009

69 Репутация

1 Guide authored

Команда

Cal Poly, Team 19-6, Maness Fall 2009 Member of Cal Poly, Team 19-6, Maness Fall 2009

CPSU-MANESS-F09S19G6

5 членов

Автор 7 руководств

Комментариев: 0

Добавить комментарий

Просмотр статистики:

За 24 часа: 0

За 7 дней: 2

За 30 дней: 15

За всё время: 5,935