Bluetooth no longer functioning after installing dual hard drives

Question

MacBook Pro 15" Unibody Mid 2010 ремонт

590вопросов Показать все

acacella7 @acacella7

Репутация: 23

1

Опубликовано: 14 фев 2015 г.

Опции

Bluetooth no longer functioning after installing dual hard drives

okay so after sucessfully removing the optical drive and installing an SSD, with the help of your guide, (Thank you!) everything seams to be running smoothly except that my bluetooth is no longer functioning. I have gone back inside to disconnect and reconnect twice now, and I do not see any physical damage, however it is still not cooperating.

Has anyone else had this problem? Any advice would be very much appreciated!

Ответ на этот вопрос У меня та же проблема

Это хороший вопрос?

Да Нет

Оценка 1

Добавить комментарий

4 Ответов

score 2 · Answer 1 · 2015-02-15T08:05:12-07:00

Наиболее полезный ответ

Dan @danj

Репутация: 479,6к

Self employed contract worker

35

329

971

Опубликовано: 15 фев 2015 г.

Опции

I would start by replacing the AirPort/Bluetooth cable 922-9296 as you may have damaged it in the process of taking it off.

Let us know how it goes.

Был ли этот ответ полезен?

Да Нет

Оценка 2

2 Комментариев:

The airport is still working completely fine though, if the cable was damaged wouldn't both the bluetooth and wifi be out of commission?

15 фев 2015 г. из acacella7

Not necessarily. Its the only thing you pulled off to get to the optical drive bay. Did you slip and nick something with your screwdriver on the AirPort card?

15 фев 2015 г. из Dan

Добавить комментарий

zzz @zzz30021 Репутация: 7,6к zzz 13 22 11 · Answer 2 · 2015-05-01T15:28:30-07:00

zzz @zzz30021

Репутация: 7,6к

zzz

13

22

11

Опубликовано: 1 мая 2015 г.

Опции

There is a piece of black tape that goes over the pins of the wifi/bluetooth/webcam connector. Then, sometimes, there is this little mesh blob thingie that goes on top of the connector/cable.

If the black tape is no longer there, but you put the mesh blob thingie back, it will short pins of the connector. So toss that little mesh thingie in the trash and you will probably have a working setup back.

Был ли этот ответ полезен?

Да Нет

Оценка 1

1 Комментарий:

"little mesh thingie" Louis are you talking about the EMI shielding pad which is conductive? Yes! I agree, you do need to make sure it's not shorting out the board.

1 мая 2015 г. из Dan

Добавить комментарий

Sebastian @sebastian27180 Репутация: 1 1 · Answer 3 · 2015-05-01T09:10:36-07:00

Sebastian @sebastian27180

Репутация: 1

1

Опубликовано: 1 мая 2015 г.

Опции

Hi there,

I have the same problem after installing a SSD. The old HDD replaced my optical drive. I replaced the Airport / Bluetooth Card (to the ...CAX one - to use hopefully handoff) without success. Next step was to replace the flex cable... Still the same Problem. WiFi works without Problems, only Bluetooth is not available.

PRAM, SMC reset didn't help either.

Has anybody an idea?

Был ли этот ответ полезен?

Да Нет

Оценка 0

2 Комментариев:

Does Bluetooth services work at all? If you are having problems setting up Handoff you should review this: Continuity Activation Tool

1 мая 2015 г. из Dan

Are you sure you have the antennas correctly connected? It you are switching the board out the connections are laid out differently between them.

1 мая 2015 г. из Dan

Добавить комментарий